3rd Annual Middle Tennessee Bash Parts Sale

[5150]

Okay this is a Parts Thread for Parts that are going to be at my cookout on March 29th:

http://67-72chevytrucks.com/vboard/s...d.php?t=265701

ALL OF THESE ITEMS THAT ARE GOING TO BE POSTED IN THIS THREAD WILL BE PICKUP ONLY!!!!!!!!

ALSO IF YOU WANT SOMETHING JUST SAY THAT YOU WANT IT, THIS IS NOT A BUY OR SELL THREAD.

99 2500 3.73 Rear End-$200
HEI Distributor-$20
Pass Side Window Regulator(I believe it's a 67-71)-$20
Third Row Back Seat out of 91 Burb with Floor Brackets AND Arm Rests-$75
Headers-$50
Chrome Fender Trim for 88-98 Trucks-$20

[5150]

and the seat

[DREAMS OF A 67]

I want the distributor and the window regulator

[5150]

Joe, they're yours

[Blue_71]

what shape is the 88-98 fender trim in?

[5150]

Good shape Josh, I can get a pic of it tomorrow. Took it off my Cruecab clean it up.

[5150]

Add some 72 disc brake spindles off of my blazer to my parts list-$40

[thelonerife]

Does anyone have a hitch?

[stanglifemike]

What are the headers for?

[5150]

small block chevy

[Blue_71]

heres my post from the tennessee board for more here to see:

TRUCK PARTS

67-72 rad support to fender corner braces, $10
69-70 center grill brace and hood latch, $25
long water pump set up, including pump, 2 pullys, and alt brackets, $50
5 lug axle shafts, came out of a 1970, i can measure them but i think they're 32", $40
headlight buckets and chrome rings, rings $5 each, buckets $10 each, or $12 as an assembly
67-72 coil spring lower rear shock brackets, $20
67-72 manual trans x-member, good shape, $35
1974 light green visors, really good shape, $30
1974 oliveish dash pad, cracking but not the worst one ive seen, $15
1978 non-tilt auto column, $30
3" leaf spring lift/lowering blocks, no u-bolts, $15
may have some more ill bring, ill have to look deeper in the building

ODDBALL PARTS

2001 Impala complete underhood wiring harness, only one connector missing, terminals there but plastic gone on that one, $75
1993 3.3 ignition module, fits alot of stuff, was working when removed, $15
04 K2500 multifunction (turn/wiper switch) was working when removed, $35, drew from owensboro has first dibs
01ish oldsmobile bravada transfer case encoder motor, from an all wheel drive, transfer case had bad clutches $35
04 cavalier 2.2 ecotec throttle body with 2 sensors and throttle cable bracket, cruise control tab is broken off but otherwise in good shape, $10
04 cavalier 2.2 ecotec ignition module and coil pack, came off running engine that was ran with no oil, still ran after being re-lubed but knocked. $40

PARTS THAT WILL ONLY BE BRUNG IF SPOKEN FOR

NP208 transfer case, unknown condition, 6 bolt round pattern, dont know what it fits but it came from a jeep guy, so im guessing jeepish type thing (chrysler?) $50
882 heads, casting beleived to be good (no visable cracks) but will need cleaned up and rebuilt, covered in surface rust from sitting, $40
78ish 010/020 350, stock bore, needs pistons, shortblock minus cam, crank good but needs surface rust knocked off from sitting, $150 (firm on this one)
87+ 350 crank. one peice rear main, had spun rod bearing, should be turnable at .010 if i remember right, $30


ill add more as i think of it. if something sounds high, im negotiable and green talks

[thelonerife]

If anyones interested I have 2 lwb sides. need some patching over wheel. inside panels good.lmk

[stonewall618]

what would it cost for the headers shipped

[Alvin]

I will be attending the meet and am looking for a pair of repro or rust-free inner fenders. I'll take one or a pair, whatever you've got!

[5150]

No shipping stonewall, this is a pickup parts thread only. sorry

[woodridge]

Here are some parts I have that I can bring:

Ford Top loader Overdrive's from the 50's or 60's- $100
Tail light repair panels, will cut from in front of marker- $25 each
68 hood $50-Sold
Step side tail gate, good driver- $30
Step side rear sill- $10
Radio delete cowl panel- $30
West coast mirrors- $25
Better than nothing GMC front bumper-$10- Sold
Big truck tow hooks- $40
Rear sway bar- $60
Olds 455, came out of my K-2500. Runs but needs built- $200
And the last pics, if you see anything you want and it's for sale I'll price it.

[woodridge]

More pics

[woodridge]

A few more.

[woodridge]

And the "If you see anything you want" pics.

[5150]

I see something I want in those last pics, PM Sent

[Blue_71]

couple more things i can bring if anyone wants, 88-98 hood, dark green, good shape, one slightly dented spot, $25

67-72 wiper arms, $10 a pair
77-87 passanger door, really good condition, one small ding in upper window frame about the size of a dime, you can kind of see the door in one of the hood pics, its the red one... came off an 83, had manual windows, no guts included, $75

[thelonerife]

Woodridge, Does the 68 hood have the usual bow down on the center ridge??

[woodridge]

I check tonight.

[Cyclone44]

Are those LWB beds any good David?, Is the black hood the 68 you have for sale?? How about the red hood what kind of shape is it in???

[woodridge]

The black hood is for sale, it's in the list above, $50. The red one goes on a truck I am working on. The bronze bed is usable, needs a little repair on the left side behind the wheel opening, $200. The Orche and white one has a few patch panels but is junk.