HELP, Pressure plate to flywheel bolt - The 1947 - Present Chevrolet & GMC Truck Message Board Network

KEH · 02-15-2003, 04:18 PM

I'm not sure which bolts I have to attach the pressure plate to flywheel. (This project has been siiting for 10 years). The Chevy dealer doesn't have any in stock either. The only 6 that I have alike is in the pic below. Is this the correct bolt?

Also, any installation tips would be appreciated. With the non-threaded shank do I just tighten until they bottom out?
It's been a few years, and I want to make sure I get it in right.

Thanks for the help..

KEH · 02-15-2003, 04:20 PM

sorry, forgot the pic.

crazy longhorn · 02-15-2003, 04:44 PM

those look to be the proper bolt, but need a lock washer. here is a link to summit(arp bolts,& pretty cheap) http://store.summitracing.com/partdetail.asp?part=10047 you should also be able to get them in a Dorman @ a local auto parts . the threads dont come all the wat to the top in the flywheel(holes are counterdrilled).....crazyL

KEH · 02-15-2003, 04:59 PM

Thanks CrazyL you're a big help. What is the Dorman that you refer to?

crazy longhorn · 02-15-2003, 05:03 PM

Dorman is the brand name, I think i found them @ O Rieleys last time in the perf hardware section . You might also find them in a MR gasket @ a local speed shop. Good luck...crazyL

02-15-2003, 04:18 PM	#1
KEH Better late than never Join Date: Dec 2001 Location: Columbus, IN Posts: 324	HELP, Pressure plate to flywheel bolt I'm not sure which bolts I have to attach the pressure plate to flywheel. (This project has been siiting for 10 years). The Chevy dealer doesn't have any in stock either. The only 6 that I have alike is in the pic below. Is this the correct bolt? Also, any installation tips would be appreciated. With the non-threaded shank do I just tighten until they bottom out? It's been a few years, and I want to make sure I get it in right. Thanks for the help.. __________________ 1970 C/10 SWB Stepside

02-15-2003, 04:20 PM	#2
KEH Better late than never Join Date: Dec 2001 Location: Columbus, IN Posts: 324	sorry, forgot the pic. Attached Images __________________ 1970 C/10 SWB Stepside

02-15-2003, 04:44 PM	#3
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	those look to be the proper bolt, but need a lock washer. here is a link to summit(arp bolts,& pretty cheap) http://store.summitracing.com/partdetail.asp?part=10047 you should also be able to get them in a Dorman @ a local auto parts . the threads dont come all the wat to the top in the flywheel(holes are counterdrilled).....crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

02-15-2003, 04:59 PM	#4
KEH Better late than never Join Date: Dec 2001 Location: Columbus, IN Posts: 324	Thanks CrazyL you're a big help. What is the Dorman that you refer to? __________________ 1970 C/10 SWB Stepside

02-15-2003, 05:03 PM	#5
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	Dorman is the brand name, I think i found them @ O Rieleys last time in the perf hardware section . You might also find them in a MR gasket @ a local speed shop. Good luck...crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.