|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-16-2008, 11:32 PM
|
#1 |
|
Registered User
Join Date: May 2007
Location: Buffalo MN
Posts: 606
|
crossmember replacement kits?
the po of my k10 butchered up the crossmember so im looking into replacing it before i decied to repair it the best i can or drill some holes and use a new one
has anyone ever used one of these kits? here is the one im looking at getting for my 68 k10 with a sbc 350 power plant http://store.summitracing.com/partde...5&autoview=sku if anyone has how hard was the install and how well do you like how it tuned out pics please if possible thanks nate 
__________________
Trial and Error, its expensive but its a mistake i most likely wont make again 1971 chevy k10 custom deluxe http://67-72chevytrucks.com/vboard/s...d.php?t=341257 1968 chevy k/10 fleet http://67-72chevytrucks.com/vboard/s...d.php?t=334731 1948 desoto custom coupe fluid drive(family heirloom) |
|
|
|
09-17-2008, 12:23 AM
|
#2 |
|
I'm a poor spectator
Join Date: Aug 2006
Location: San Antonio, Tx
Posts: 2,287
|
Re: crossmember replacement kits?
__________________
2006 Jeep Unlimited IMPACT ORANGE 1993 Chevy 2500 4x4 ExCab LWB 454/NV4500 Tow rig  1977 Ford F100 2x4 LWB 1st truck I owned, still have it!!!  1979 Ford F150 4x4 SWB Built Ford Tough!!!  1971 Chevy Blazer 350 / SM465 / NP205 UNDER CONSTRUCTION Soon to have a LQ4 6.0!!! |
|
|
|
|
09-17-2008, 12:54 AM
|
#3 | |
|
Future TOTM Winner
Join Date: Aug 2006
Location: Bulverde, TX
Posts: 2,692
|
Re: crossmember replacement kits?
Quote:
__________________
72 Chevy CST K5 HIGHLANDER BLAZER Getting a 6.0,NV4500,NP205,14BFF (Currently laying all over the place in little pieces) 72 Chevy swb step-side "LS" 6.0 Here's a build thread of sorts 2002 HD2500 Crew Cab, 8.1L Allison 4x4 Daily Driver Check it out www.lsdyno.com |
|
|
|
|
|
09-17-2008, 06:05 AM
|
#4 |
|
Registered User
Join Date: May 2001
Location: Bethlehem, GA, USA
Posts: 389
|
Re: crossmember replacement kits?
I have bought some other parts for my 4x4 from DIY4x and they are top notch. What I bought lined up perfectly and bolted right in. Everything is BEEFY too. Highly recommend them.
Tom
__________________
No more dragtruck for me. I'm building a new ride though. It's a '71 fleetside, 400 sbc, 700R4. Working on it now, finally. Soon to have Edelbrock Pro Flo EFI, Vintage Air, 1 piece windows, buddy buckets, etc. My new build thread: http://67-72chevytrucks.com/vboard/s...17#post2861817 Best pass with the old dragtruck: 5.32 @ 131.6 mph 1/8 mile w/ a 1.25 60' Fogger/Plate 2003 Best pass with the street 406 hydraulic roller motor w/ mild plate tuneup 5.93 @ 114 mph 1/8 mile w/ a 1.29 60' 2003 or 2004 |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
