|
11-04-2008, 12:16 AM
|
#1 |
|
86 C10
Join Date: Sep 2007
Location: Ga.
Posts: 416
|
f9000's ?'s
this might be a stupid question but on the 9000's can i use 3/8 line or does it have to be 1/4th?
Would it be a problem? I don't think it would but just asking because i have conti's 2600's and there are rubbing on the inside of the notch or where rubbing and i thought it wouldn't be a problem but today they went boom! (after about 6 months or driving) and i dont to what to change the airline out if i don't have to. One more question would they just bolt on to the existing holes of my conti's. Thanks!
__________________
1986 C10 2001 chevy silverado purchased 8-29-09 sold 2004 silverado purchased 8-27-10 sold 
|
|
|
|
11-04-2008, 01:41 AM
|
#2 |
|
Senior Member
Join Date: Dec 2003
Location: Mesa,Az
Posts: 3,981
|
Re: f9000's ?'s
No need to change the airline. Just make sure you get the correct fitting.
__________________
www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003! |
|
|
|
|
11-04-2008, 02:04 AM
|
#3 | |
|
86 C10
Join Date: Sep 2007
Location: Ga.
Posts: 416
|
Re: f9000's ?'s
Quote:
would they bolt in the existing holes of the 2600's.
__________________
1986 C10 2001 chevy silverado purchased 8-29-09 sold 2004 silverado purchased 8-27-10 sold
|
|
|
|
|
|
11-04-2008, 09:37 AM
|
#4 |
|
Registered User
Join Date: Jul 2007
Location: minnesota
Posts: 191
|
Re: f9000's ?'s
meaning if you have 3/8 line and 3/8 fittings your gonna need some type of reducer or step down fitting to 1/4.
__________________
1981 - C-10 SCSB Planning on putting this thing on it's rocker! 
|
|
|
|
|
11-04-2008, 11:31 AM
|
#5 |
|
It'd be alot cooler if you did
Join Date: May 2003
Location: Three Rivers, MI
Posts: 2,345
|
Re: f9000's ?'s
The f9000's take a single 3/8-16 bolt right in the middle for the bottom and two 3/8-16 bolts in the top.
|
|
|
|
|
11-04-2008, 11:52 PM
|
#6 | ||
|
86 C10
Join Date: Sep 2007
Location: Ga.
Posts: 416
|
Re: f9000's ?'s
Quote:
Quote:
__________________
1986 C10 2001 chevy silverado purchased 8-29-09 sold 2004 silverado purchased 8-27-10 sold
|
||
|
|
|
|
11-08-2008, 04:16 PM
|
#7 |
|
Registered User
Join Date: Oct 2008
Location: Largo, Florida
Posts: 158
|
Re: f9000's ?'s
You can buy a one piece fitting that is 1/4 NPT and 3/8 line, we have them here for that purpose. As for as bolting them in the same place as a 2600# bag, yes and no. You may have to drill a center hole on lower plate if not so equipped, and drill to closer holes for the upper mounts.
|
|
|
|
|
11-08-2008, 04:19 PM
|
#8 |
|
It'd be alot cooler if you did
Join Date: May 2003
Location: Three Rivers, MI
Posts: 2,345
|
Re: f9000's ?'s
I ran 1/2" line to my f9000s, one fitting.
|
|
|
|
|
11-08-2008, 04:26 PM
|
#9 |
|
Registered User
Join Date: Oct 2008
Location: Largo, Florida
Posts: 158
|
Re: f9000's ?'s
Yes those are available too!!
|
|
|
|
|
11-08-2008, 11:37 PM
|
#10 | |
|
86 C10
Join Date: Sep 2007
Location: Ga.
Posts: 416
|
Re: f9000's ?'s
Quote:
__________________
1986 C10 2001 chevy silverado purchased 8-29-09 sold 2004 silverado purchased 8-27-10 sold
|
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
