Support Bearing...what way round?? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

eightbanger · 03-06-2009, 11:42 AM

I have made a note of the one I removed, but just incase the old one had not been installed correctly I thought i'd double check with you guys.

This way?

Or this way?

eightbanger · 03-06-2009, 01:12 PM

Hello!....is anybody there??

Andy4639 · 03-06-2009, 02:05 PM

Mine has the other bearing sorry I can't help you. I would think it would be the second picture though.

boundstaffpress · 03-06-2009, 02:23 PM

yes, only in needs to be farther down the shaft.

eightbanger · 03-06-2009, 04:13 PM

Thanks Andy & Justin....your guesses would correspond with the way the original was installed.

My wife said it needed to be further down the shaft too

sneakysnake · 03-06-2009, 04:51 PM

IIRC the flare on the rubber goes to the rear. use a piece of pipe the is the same size as the inner race to drive it on the shaft fully.

eightbanger · 03-06-2009, 05:05 PM

Thats a good idea for fitting this, thanks for the heads up sneakysnake . I was going down the route of finding somewhere or somebody with a press to get this thing back on, didn't mind destroying the old one getting it off.

scott's69 · 03-06-2009, 06:57 PM

The wife is right!!!

03-06-2009, 11:42 AM	#1
eightbanger 454 MAKES IT ROAR Join Date: Jan 2008 Location: Essex, U.K Posts: 2,701	Support Bearing...what way round?? I have made a note of the one I removed, but just incase the old one had not been installed correctly I thought i'd double check with you guys. This way? Or this way? __________________ Nigel. An American living in a British body. 1971 Chevy Cheyenne 10 454 "In a time of universal deceit, telling the truth becomes a revolutionary act." - George Orwell "When injustice becomes law, resistance becomes duty" - Thomas Jefferson No more pain. 03.12.60 -- 12.28.10 http://www.youtube.com/Eightbanger

03-06-2009, 01:12 PM	#2
eightbanger 454 MAKES IT ROAR Join Date: Jan 2008 Location: Essex, U.K Posts: 2,701	Re: Support Bearing...what way round?? Hello!....is anybody there?? __________________ Nigel. An American living in a British body. 1971 Chevy Cheyenne 10 454 "In a time of universal deceit, telling the truth becomes a revolutionary act." - George Orwell "When injustice becomes law, resistance becomes duty" - Thomas Jefferson No more pain. 03.12.60 -- 12.28.10 http://www.youtube.com/Eightbanger

03-06-2009, 02:05 PM	#3
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,936	Re: Support Bearing...what way round?? Mine has the other bearing sorry I can't help you. I would think it would be the second picture though. __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

03-06-2009, 02:23 PM	#4
boundstaffpress Jamie Hyneman is my twin Join Date: Nov 2005 Location: La Junta, Colorado Posts: 705	Re: Support Bearing...what way round?? yes, only in needs to be farther down the shaft. __________________ Justin SOLD 1967 K10 Fleetside, 283, Front and Rear Posi SOLD Color Wiring Diagrams Now in High Resolution V8 and Cab and Cab and Chassis

03-06-2009, 04:13 PM	#5
eightbanger 454 MAKES IT ROAR Join Date: Jan 2008 Location: Essex, U.K Posts: 2,701	Re: Support Bearing...what way round?? Thanks Andy & Justin....your guesses would correspond with the way the original was installed. My wife said it needed to be further down the shaft too __________________ Nigel. An American living in a British body. 1971 Chevy Cheyenne 10 454 "In a time of universal deceit, telling the truth becomes a revolutionary act." - George Orwell "When injustice becomes law, resistance becomes duty" - Thomas Jefferson No more pain. 03.12.60 -- 12.28.10 http://www.youtube.com/Eightbanger Last edited by eightbanger; 03-06-2009 at 04:15 PM.

03-06-2009, 04:51 PM	#6
sneakysnake It's a catastrophic success. Join Date: Jan 2003 Location: Oklahoma Posts: 2,077	Re: Support Bearing...what way round?? IIRC the flare on the rubber goes to the rear. use a piece of pipe the is the same size as the inner race to drive it on the shaft fully. Attached Images

03-06-2009, 05:05 PM	#7
eightbanger 454 MAKES IT ROAR Join Date: Jan 2008 Location: Essex, U.K Posts: 2,701	Re: Support Bearing...what way round?? Thats a good idea for fitting this, thanks for the heads up sneakysnake . I was going down the route of finding somewhere or somebody with a press to get this thing back on, didn't mind destroying the old one getting it off. __________________ Nigel. An American living in a British body. 1971 Chevy Cheyenne 10 454 "In a time of universal deceit, telling the truth becomes a revolutionary act." - George Orwell "When injustice becomes law, resistance becomes duty" - Thomas Jefferson No more pain. 03.12.60 -- 12.28.10 http://www.youtube.com/Eightbanger

03-06-2009, 06:57 PM	#8
scott's69 WORTHLESS CRUISERS Join Date: May 2002 Location: Lancaster, SC Posts: 237	Re: Support Bearing...what way round?? The wife is right!!! __________________ Scott Hammond Lancaster, SC 1969 Chevy2005 Chevy Silverado Z71 72 Chevy 1972 SWB 454 If you don't live for something, then you'll die for nothing. www.xclusive-images.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.