|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-18-2003, 04:37 PM
|
#1 |
|
FightingFire Saving Lives
Join Date: Mar 2003
Location: Tulsa, Oklahoma
Posts: 65
|
How To Identify My Axles
HEY CHEVY BROTHERS,
JUST CURIOUS HOW I CAN IDENTIFY MY AXLES ON MY BABY. THE GLOVE BOX DOOR IS TELLING ME 3:73 WILL THAT BE FRONT AND BACK, IS THERE A STAMP SOMEWHERE ON THE AXLE'S THAT WILL CLEAR THIS UP FOR ME. I JUST WANT TO MAKE SURE SHE HAS THE ORIGINAL AXLES. JUST NEED TO KNOW WHERE TO LOOK. THANKS FELLERS. FIREMANCHUCK, TULSA, OK  1972 4X4 FLEETSIDE SWB 350 SMC 4-SPEED |
|
|
|
03-18-2003, 05:07 PM
|
#2 |
|
Life is Good !
Join Date: Mar 2002
Location: Hollister, Ca.
Posts: 1,992
|
I know if you take the covers off there are #'s on the ring gear, if you post those #'s someone will be able to help you. That's the way I have always checked them.
Welcome to the board, Landon
__________________
'72 Chevy C10 4x4 shortbed "Project" '71 Chevy C10 2wd longbed "partsrunner" '91 Chevy Burb 4x4 "kidrunner" '14 Honda Accord Sport "commuter" |
|
|
|
|
03-18-2003, 06:00 PM
|
#3 |
|
Registered User
Join Date: Jan 2003
Location: Washington State
Posts: 8,831
|
Generally, there would be a code on the axle housing. About 6" out from the main housing..............
__________________
1970 Chev CST 2003 Harley Fatboy 1975 Chevrolet Step Van 1956 Chev Bel Air 1977 Blazer 2WD For Sale $3000.00 1978 Blazer 2WD For Sale $7000.00 1978 Silverado 2005 Monte Carlo |
|
|
|
|
03-18-2003, 06:05 PM
|
#4 |
|
Post Whore
 
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
|
The front axle should be a Dana 44 and will have D44 stamped in the webbing on one side of the differential. Not positive of markings on the rear axle. It is not uncommon to find a slightly different gear ratio in the front axle than the rear axle, usually just off by .01.
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
03-18-2003, 06:51 PM
|
#5 |
|
Registered User
Join Date: Feb 2003
Location: Wichita Kansas
Posts: 223
|
If they are 3.73 gears there will be a 41:11 stamped on the gear inside of the pan. I would go ahead and pull pan to check, being a 30 year old truck probably could use some new oil.
__________________
1972 chevy k10 4x4 longbed 4-inch lift, 3.73 front/rears, frame off nearly complete 1972 chevy k10 4x4 longbed parts truck, known as the "ugly green machine" 1990 GMC 3/4 shortbed ext cab Always in need of 67-72 parts in central ks. |
|
|
|
|
03-18-2003, 07:43 PM
|
#6 |
|
Registered User
Join Date: Dec 2001
Location: New Richmond, WI
Posts: 547
|
That's 41 teeth on the ring and 11 teeth on the pinion. 41/11=3.727272 or 3.73 Just had to throgh that out there because its the one thing in the world that I know.
__________________
Eric 1969 K20, 465/205 package |
|
|
|
|
03-19-2003, 06:01 AM
|
#7 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
If they are stock they should be a Dana/Spicer 44 up front and a GM 12 bolt in the rear.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
