Calling FlamingBig10, TVBlazer78, or Captkaos - The 1947 - Present Chevrolet & GMC Truck Message Board Network

S10Fan · 08-18-2009, 05:18 AM

I have a pair of the custom door panels from Captkaos and I know you guys do too. Here's my question. How did you attach the arm rest to the back side of the panel? Looking at the lip around the arm rest I don't see how there will be enough area to use the dual lock fasteners. I don't see how the abs glue would work because material will be pulled through the hole from the outside of the panel.

I have a couple ideas in my head I'm just concerned my hands will screw them up. LOL.

Bryan

flamingbig10 · 08-18-2009, 11:10 AM

mines wedged in with the vinyl

S10Fan · 08-19-2009, 05:34 AM

Thanks Aaron. Is that a photo before installation? I don't see any of the dual lock fasteners.

Bryan

andrewmp6 · 08-19-2009, 07:12 AM

Good velcro will hold them on tight.

flamingbig10 · 08-19-2009, 02:05 PM

Quote:

Originally Posted by S10Fan

Thanks Aaron. Is that a photo before installation? I don't see any of the dual lock fasteners.

Bryan

no problem, it was, but on the driver side the fasteners wouldn't hold up, the door panel would get hung on the weatherstripping so added a couple hidden screws and no more problems

08-18-2009, 05:18 AM	#1
S10Fan Old Heap Driver Join Date: Mar 2008 Location: Newport News, Va Posts: 2,642	Calling FlamingBig10, TVBlazer78, or Captkaos I have a pair of the custom door panels from Captkaos and I know you guys do too. Here's my question. How did you attach the arm rest to the back side of the panel? Looking at the lip around the arm rest I don't see how there will be enough area to use the dual lock fasteners. I don't see how the abs glue would work because material will be pulled through the hole from the outside of the panel. I have a couple ideas in my head I'm just concerned my hands will screw them up. LOL. Bryan __________________ _____________________________ Bryan '99 Silverado 1500, 4.3, 5-speed, reg cab, short bed '50 Chevy 2DR Hard Top, 350/350, M2 Front End, 3:08 gear, cruiser. '40 F**d Sedan, all Chevy power, Heidt's front end, TCI rear, nice driver.

08-18-2009, 11:10 AM	#2
flamingbig10 6.0 powered square Join Date: Feb 2008 Location: Mesquite texas Posts: 3,459	Re: Calling FlamingBig10, TVBlazer78, or Captkaos mines wedged in with the vinyl __________________ Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326

08-19-2009, 05:34 AM	#3
S10Fan Old Heap Driver Join Date: Mar 2008 Location: Newport News, Va Posts: 2,642	Re: Calling FlamingBig10, TVBlazer78, or Captkaos Thanks Aaron. Is that a photo before installation? I don't see any of the dual lock fasteners. Bryan __________________ _____________________________ Bryan '99 Silverado 1500, 4.3, 5-speed, reg cab, short bed '50 Chevy 2DR Hard Top, 350/350, M2 Front End, 3:08 gear, cruiser. '40 F**d Sedan, all Chevy power, Heidt's front end, TCI rear, nice driver.

08-19-2009, 07:12 AM	#4
andrewmp6 Registered User Join Date: Jan 2009 Location: Louisville,Ky Posts: 5,811	Re: Calling FlamingBig10, TVBlazer78, or Captkaos Good velcro will hold them on tight.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.