new track results! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Tracy Focht · 04-05-2003, 06:08 PM

Ran it Friday night, wind was 10-15 out of the north, track due east. And since this was the first TNT of the year, track was full! So I was only able to make two runs, and did no tweaking,jetting or anything.

First run:
R/T 0.785
60ft 1.89
330ft 5.41
1/8 ET 8.41
1/8 MPH 81.38
1/4 13.27
MPH 98.87

Second run:
R/T 0.658
60ft 1.84
330 ft 5.37
1/8 ET 8.36
1/8 MPH 81.53
1/4 13.21
MPH 99.09

carb is still jetted 73/73's, timing at 38 total, 27.2" ET streets, 3000 stall,and shift at 6000-6100.

so not quite the 12's I was hoping, but it was cold (40's) and not alot of traction. So I hope with a sunny decent track and some tune time, I can squeeze a low 12 out of it.

Jast sharing the run....

*dtlilly* · 04-05-2003, 06:25 PM

nice et's. overall consistant results.

383 Stroker · 04-05-2003, 06:51 PM

Sounds good! What size ET Streets are you running and how do you like them?

GMC71k20 · 04-05-2003, 11:19 PM

cant wait until i get a truck thats track worthy, you hvae any pics?

**Yukon Jack** · 04-06-2003, 09:10 AM

Sounds awesome to me. Refresh my memory on how that compares to your old engine!

Mike C · 04-06-2003, 04:58 PM

Gettin close!

Some suggestions for power: Underdrive pulleys, not radical, but slightly slow your accessories. The other is MANDATORY. Cold air induction. Get you one of those aftermarket dual snorkel ram-air air cleaners. I know, they are expensive, but worth it. My GM cowl air cleaner and a Moroso underdrive pulley dropped my car from 13.10 to 12.80s. The 60' time is excellent, but MPH at the end seems a little low for that 406. Should pcik up as you get a few more miles on it I would think.

Still can't email your, stupid SPAM filter.

Tracy Focht · 04-07-2003, 09:58 AM

Tire are a 28x11.50 ET Streets, love them!

The 383 ran a 13.56 and was tuned as best I could get....this one, timing curve hasn't been done, or the carb, it's right out of the box and floats set. Still has 73/73 jets' as the other Holley had 78/82's...but since this is an HP carb, will have to play with it more.

Mike, I have the deep groove pullies, but may have to try the ram air setup...sound interesting.

You should also be able to email me now, as we've taken the filter off my emails coming in....try it when you have time.

*Randy70C-10* · 04-07-2003, 10:26 AM

Hey Tracy, have you port-matched the intake and heads yet? It seems to be one of the easiest things to do for a horsepower gain, all you need is a die grinder.

Tracy Focht · 04-07-2003, 10:40 AM

nope,that's one thing i wished I would have done...

barn9 · 04-07-2003, 12:33 PM

Hey Tracy, when are you bringing the truck up for paint? I'm lookin' forward to you buying my lunch, LOL!

Tracy Focht · 04-07-2003, 01:13 PM

Quote:

Originally posted by barn9
Hey Tracy, when are you bringing the truck up for paint? I'm lookin' forward to you buying my lunch, LOL!

next Monday...was supposed to be today, but we have a big cruise all day Saturday here, and I didn't want to miss it....next week?

04-05-2003, 06:08 PM	#1
Tracy Focht Registered User Join Date: Dec 1999 Location: Stillwater, OK 74075 Posts: 2,936	new track results! Ran it Friday night, wind was 10-15 out of the north, track due east. And since this was the first TNT of the year, track was full! So I was only able to make two runs, and did no tweaking,jetting or anything. First run: R/T 0.785 60ft 1.89 330ft 5.41 1/8 ET 8.41 1/8 MPH 81.38 1/4 13.27 MPH 98.87 Second run: R/T 0.658 60ft 1.84 330 ft 5.37 1/8 ET 8.36 1/8 MPH 81.53 1/4 13.21 MPH 99.09 carb is still jetted 73/73's, timing at 38 total, 27.2" ET streets, 3000 stall,and shift at 6000-6100. so not quite the 12's I was hoping, but it was cold (40's) and not alot of traction. So I hope with a sunny decent track and some tune time, I can squeeze a low 12 out of it. Jast sharing the run....

04-05-2003, 06:51 PM	#3
383 Stroker Registered User Join Date: Aug 2001 Location: Jesup, GA Posts: 571	Sounds good! What size ET Streets are you running and how do you like them? __________________ Video's of my Truck Racing 1967 C-10, 383ci Sbc, TH350, 3200 stall, 3.73 gear

04-06-2003, 09:10 AM	#5
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,684	Sounds awesome to me. Refresh my memory on how that compares to your old engine! __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

04-06-2003, 04:58 PM	#6
Mike C Registered User Join Date: Dec 1999 Location: Austin, TX, USA Posts: 7,723	Gettin close! Some suggestions for power: Underdrive pulleys, not radical, but slightly slow your accessories. The other is MANDATORY. Cold air induction. Get you one of those aftermarket dual snorkel ram-air air cleaners. I know, they are expensive, but worth it. My GM cowl air cleaner and a Moroso underdrive pulley dropped my car from 13.10 to 12.80s. The 60' time is excellent, but MPH at the end seems a little low for that 406. Should pcik up as you get a few more miles on it I would think. Still can't email your, stupid SPAM filter. __________________ 44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax

04-07-2003, 12:33 PM	#10
barn9 Half a bubble off! Join Date: Jun 2000 Location: Winfield, Ks, USA Posts: 5,588	Hey Tracy, when are you bringing the truck up for paint? I'm lookin' forward to you buying my lunch, LOL! __________________ Just call me LB. '71 Cheyenne, 402BB, hauls blondes, brunettes, or redheads.

04-05-2003, 06:25 PM	#2
dtlilly Account Suspended Join Date: Jan 2003 Location: Shadow of Lambeau Field Posts: 5,597	nice et's. overall consistant results.

04-05-2003, 11:19 PM	#4
GMC71k20 Registered User Join Date: Aug 2002 Location: mass Posts: 1,277	cant wait until i get a truck thats track worthy, you hvae any pics?

04-07-2003, 09:58 AM	#7
Tracy Focht Registered User Join Date: Dec 1999 Location: Stillwater, OK 74075 Posts: 2,936	Tire are a 28x11.50 ET Streets, love them! The 383 ran a 13.56 and was tuned as best I could get....this one, timing curve hasn't been done, or the carb, it's right out of the box and floats set. Still has 73/73 jets' as the other Holley had 78/82's...but since this is an HP carb, will have to play with it more. Mike, I have the deep groove pullies, but may have to try the ram air setup...sound interesting. You should also be able to email me now, as we've taken the filter off my emails coming in....try it when you have time.

04-07-2003, 10:26 AM	#8
Randy70C-10 Account Suspended Join Date: Mar 2001 Location: Virginia Beach, Va. U.S.A. Posts: 15,320	Hey Tracy, have you port-matched the intake and heads yet? It seems to be one of the easiest things to do for a horsepower gain, all you need is a die grinder.

04-07-2003, 10:40 AM	#9
Tracy Focht Registered User Join Date: Dec 1999 Location: Stillwater, OK 74075 Posts: 2,936	nope,that's one thing i wished I would have done...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.