corporate vs dana 44 front axle backing plates - The 1947 - Present Chevrolet & GMC Truck Message Board Network

cparman · 11-14-2009, 09:38 PM

This might be confusing. I have a friend that is building a SWB 3/4 ton 4X4. Started life as a swb 1/2 ton, but he has a small junk yard, and put together 3/4 ton 8 lug front and rear axle assys, along with a transfer case and a big block. My friend was looking for a front hub, which WHISKEYDENTED helped with. Went by to check on the progress today, and Donald was perplexed about why he could not get the front brake calipers to mount? I want all to know that he has pieced and parted together what he has completed.

We went for a walk today, and he showed me a " corporate " rear end where the front brake rotor did not extend past the dustshield/backing plate.

The truck build has the front rotor extending past the caliper mount/backing plate.

He had another set of backing plates that did resolve his problem, but he/I would like to know what is up with this.

I do have a couple of pics, but they are on my phone. may not be smart enough to post them.

msgross · 11-14-2009, 09:44 PM

hmm, there are a few different options when you start mixing 1/2 and 3/4 ton.. and corp and dana axles... Send pics of what you have, not sure if i'll be of any help but I did build a corp 10 out of a dana 44 axle. Some items swapped and some didn't.

I also have a spare front backing plate

msgross · 11-25-2009, 10:33 PM

any updates on what you found?

11-14-2009, 09:38 PM	#1
cparman sharp as a marble Join Date: Jan 2007 Location: atlantic beach,florida Posts: 1,082	corporate vs dana 44 front axle backing plates This might be confusing. I have a friend that is building a SWB 3/4 ton 4X4. Started life as a swb 1/2 ton, but he has a small junk yard, and put together 3/4 ton 8 lug front and rear axle assys, along with a transfer case and a big block. My friend was looking for a front hub, which WHISKEYDENTED helped with. Went by to check on the progress today, and Donald was perplexed about why he could not get the front brake calipers to mount? I want all to know that he has pieced and parted together what he has completed. We went for a walk today, and he showed me a " corporate " rear end where the front brake rotor did not extend past the dustshield/backing plate. The truck build has the front rotor extending past the caliper mount/backing plate. He had another set of backing plates that did resolve his problem, but he/I would like to know what is up with this. I do have a couple of pics, but they are on my phone. may not be smart enough to post them. Attached Images Last edited by cparman; 11-14-2009 at 09:41 PM.

11-14-2009, 09:44 PM	#2
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: corporate vs dana 44 front axle backing plates hmm, there are a few different options when you start mixing 1/2 and 3/4 ton.. and corp and dana axles... Send pics of what you have, not sure if i'll be of any help but I did build a corp 10 out of a dana 44 axle. Some items swapped and some didn't. I also have a spare front backing plate __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

11-25-2009, 10:33 PM	#3
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: corporate vs dana 44 front axle backing plates any updates on what you found? __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.