Is this the right part??? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Mike Quillici · 02-01-2010, 01:25 AM

I have a hole in the passenger side floor of my C-10 at the point where the floor curves up toward the firewall at the seam of the vertical kick panel. Can somebody tell me if this is the correct replacement part? I think it looks right.

Thanks,

Mike

http://www.classicparts.com/1967-72-...info/45%2D942/

whatnow123 · 02-01-2010, 01:31 AM

It's the right part based on the discription however, the photo is mis-leading as it's hard to tell which side that one is for.

Mike Quillici · 02-01-2010, 01:42 AM

Yeah. I was having a hard time with that too, which is why I asked. Thanks for the info.

Mike Quillici · 02-05-2010, 12:41 AM

I'm trying to figure out what my options are to patch the holes in my floor board. I'm not trying to create a show truck, but a quality work truck that doesn't leak and to stop the rust from continuing to propagate. I will ultimately be covering it with a new carpet, so I don't much care what it looks like.

vectorit · 02-05-2010, 12:55 AM

Don't know about your rig.
But it looks like the front passenger floor in my 68 burb, with the body mount to frame bolt hole recess.

Mike Quillici · 02-05-2010, 12:58 AM

Yeup. That is it exactly.

02-01-2010, 01:25 AM	#1
Mike Quillici Registered User Join Date: Oct 2009 Location: Sacramento, CA Posts: 161	Is this the right part??? I have a hole in the passenger side floor of my C-10 at the point where the floor curves up toward the firewall at the seam of the vertical kick panel. Can somebody tell me if this is the correct replacement part? I think it looks right. Thanks, Mike http://www.classicparts.com/1967-72-...info/45%2D942/ __________________ 1972 Chevy C-10 ~ 188,000 miles give or take

02-01-2010, 01:31 AM	#2
whatnow123 Registered User Join Date: Oct 2006 Location: Arizona Posts: 835	Re: Is this the right part??? It's the right part based on the discription however, the photo is mis-leading as it's hard to tell which side that one is for. __________________ 67 Short Step, 355, 700R 4.11 posi rear, 4/6 drop Discs on all 4 corners. Build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=219094

02-01-2010, 01:42 AM	#3
Mike Quillici Registered User Join Date: Oct 2009 Location: Sacramento, CA Posts: 161	Re: Is this the right part??? Yeah. I was having a hard time with that too, which is why I asked. Thanks for the info. __________________ 1972 Chevy C-10 ~ 188,000 miles give or take

02-05-2010, 12:41 AM	#4
Mike Quillici Registered User Join Date: Oct 2009 Location: Sacramento, CA Posts: 161	Re: Is this the right part??? I'm trying to figure out what my options are to patch the holes in my floor board. I'm not trying to create a show truck, but a quality work truck that doesn't leak and to stop the rust from continuing to propagate. I will ultimately be covering it with a new carpet, so I don't much care what it looks like. __________________ 1972 Chevy C-10 ~ 188,000 miles give or take

02-05-2010, 12:55 AM	#5
vectorit What? Join Date: Jun 2007 Location: Southern California Posts: 7,617	Re: Is this the right part??? Don't know about your rig. But it looks like the front passenger floor in my 68 burb, with the body mount to frame bolt hole recess. __________________ Chris 1968 K20 Suburban 1972 K10 LWB PU

02-05-2010, 12:58 AM	#6
Mike Quillici Registered User Join Date: Oct 2009 Location: Sacramento, CA Posts: 161	Re: Is this the right part??? Yeup. That is it exactly. __________________ 1972 Chevy C-10 ~ 188,000 miles give or take

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.