Stock A arms blasted and powder coated. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

phantom dually · 04-29-2003, 12:23 AM

I have a set of stock arms from a 83 1/2 ton. They have been blasted and powder coated black. The lower arm have had the stop removed to clear a air bag. They are a great way to swap out your old ones with no downtime. The shaft are also included and are powdered as well. I do have all new bushings and balljoints that can go for a very reasonable price. Arms only will take $130 shipped. These should fit all 1/2 ton and others from 60's to mid 80's. Balljoints and bushings will go for a additional $100 shipped. 4 lower bushings 4 upper bushings and 4 new moog ball joints. Ball joints alone were $100. All parts are new!!

phantom dually · 04-29-2003, 12:24 AM

lowers arms

78SilveradoSWB · 04-29-2003, 01:58 PM

Are the "A" arm bushings Energy Suspension, PST, or OEM?

stepn67 · 04-29-2003, 03:26 PM

Hey Phantom,
Been looking for a set for my '67 - But would the shipping cost to AZ (85712) kill me?

phantom dually · 04-29-2003, 09:55 PM

I will sell for $130 shipped as said!!

phantom dually · 05-01-2003, 04:14 PM

The bushings and ball joints have been Sold But I still have the a arms and shafts.

low 84 · 05-01-2003, 08:52 PM

okay. i am intrested but what exactly is it? 4 arms and shafts. are the shafts installed on the arms with bushings or are they apart? and how good of a job is the powdercoating, any dust or junk in it?

i will probly take them off you hands. thanks

low 84 · 05-02-2003, 12:19 PM

TTT

phantom dually · 05-02-2003, 01:12 PM

Im new to this so what is TTT. The arms are not 100% perfect but a great step over stock. I have all the arms and the 2 lower shafts. I do not have the upper shafts. They are really clean. The uppers look better than the lowers becuase of a few scraps when i took off the bump stops.

78SilveradoSWB · 05-02-2003, 01:48 PM

TTT or ^^^ is used to bump the post up near the top for visability.

low 84 · 05-02-2003, 09:01 PM

i'll take em. lets move this to pm

low 84 · 05-03-2003, 11:38 AM

did you get my pm? please respond if you want to sell these.

phantom dually · 05-03-2003, 01:46 PM

Sent you e mail your pm box is full.

04-29-2003, 12:23 AM	#1
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	Stock A arms blasted and powder coated. I have a set of stock arms from a 83 1/2 ton. They have been blasted and powder coated black. The lower arm have had the stop removed to clear a air bag. They are a great way to swap out your old ones with no downtime. The shaft are also included and are powdered as well. I do have all new bushings and balljoints that can go for a very reasonable price. Arms only will take $130 shipped. These should fit all 1/2 ton and others from 60's to mid 80's. Balljoints and bushings will go for a additional $100 shipped. 4 lower bushings 4 upper bushings and 4 new moog ball joints. Ball joints alone were $100. All parts are new!! Attached Images __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

04-29-2003, 12:24 AM	#2
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	lowers lowers arms Attached Images __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

04-29-2003, 01:58 PM	#3
78SilveradoSWB Senior Member Join Date: Apr 2002 Location: Beaverton, OR Posts: 1,615	Are the "A" arm bushings Energy Suspension, PST, or OEM? __________________ Mitch 1978 Chevrolet Silverado C 10 454 BB, TH400

04-29-2003, 09:55 PM	#5
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	I will sell for $130 shipped as said!! __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

05-01-2003, 04:14 PM	#6
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	The bushings and ball joints have been Sold But I still have the a arms and shafts. __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

04-29-2003, 03:26 PM	#4
stepn67 Junior Member Join Date: Dec 2002 Location: Tucson, AZ Posts: 140	Hey Phantom, Been looking for a set for my '67 - But would the shipping cost to AZ (85712) kill me?

05-01-2003, 08:52 PM	#7
low 84 Registered User Join Date: Jan 2002 Location: Houston, TX Posts: 2,144	okay. i am intrested but what exactly is it? 4 arms and shafts. are the shafts installed on the arms with bushings or are they apart? and how good of a job is the powdercoating, any dust or junk in it? i will probly take them off you hands. thanks __________________ '51 F100, backhalf with a narrowed 9 and coil overs, 18.5" mickeys, monte front clip, +400" sbc in the works '05 1500 Crew Cab RIP '84 swb 5/7 drop, solid cammed 408 w/ fully ported dart heads, th350 w/ 10 inch hughes, 12 bolt w/ 3.73 richmonds and a locker '80 swb 4x4 in progress: 7" lift, 350 th350/np205, d44 and 1.5" ORD tie rod, 14BFF w/discs , armored diff covers, 40" MTR's

05-02-2003, 12:19 PM	#8
low 84 Registered User Join Date: Jan 2002 Location: Houston, TX Posts: 2,144	TTT __________________ '51 F100, backhalf with a narrowed 9 and coil overs, 18.5" mickeys, monte front clip, +400" sbc in the works '05 1500 Crew Cab RIP '84 swb 5/7 drop, solid cammed 408 w/ fully ported dart heads, th350 w/ 10 inch hughes, 12 bolt w/ 3.73 richmonds and a locker '80 swb 4x4 in progress: 7" lift, 350 th350/np205, d44 and 1.5" ORD tie rod, 14BFF w/discs , armored diff covers, 40" MTR's

05-02-2003, 01:12 PM	#9
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	Im new to this so what is TTT. The arms are not 100% perfect but a great step over stock. I have all the arms and the 2 lower shafts. I do not have the upper shafts. They are really clean. The uppers look better than the lowers becuase of a few scraps when i took off the bump stops. __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

05-02-2003, 01:48 PM	#10
78SilveradoSWB Senior Member Join Date: Apr 2002 Location: Beaverton, OR Posts: 1,615	TTT or ^^^ is used to bump the post up near the top for visability. __________________ Mitch 1978 Chevrolet Silverado C 10 454 BB, TH400

05-02-2003, 09:01 PM	#11
low 84 Registered User Join Date: Jan 2002 Location: Houston, TX Posts: 2,144	i'll take em. lets move this to pm __________________ '51 F100, backhalf with a narrowed 9 and coil overs, 18.5" mickeys, monte front clip, +400" sbc in the works '05 1500 Crew Cab RIP '84 swb 5/7 drop, solid cammed 408 w/ fully ported dart heads, th350 w/ 10 inch hughes, 12 bolt w/ 3.73 richmonds and a locker '80 swb 4x4 in progress: 7" lift, 350 th350/np205, d44 and 1.5" ORD tie rod, 14BFF w/discs , armored diff covers, 40" MTR's

05-03-2003, 11:38 AM	#12
low 84 Registered User Join Date: Jan 2002 Location: Houston, TX Posts: 2,144	did you get my pm? please respond if you want to sell these. __________________ '51 F100, backhalf with a narrowed 9 and coil overs, 18.5" mickeys, monte front clip, +400" sbc in the works '05 1500 Crew Cab RIP '84 swb 5/7 drop, solid cammed 408 w/ fully ported dart heads, th350 w/ 10 inch hughes, 12 bolt w/ 3.73 richmonds and a locker '80 swb 4x4 in progress: 7" lift, 350 th350/np205, d44 and 1.5" ORD tie rod, 14BFF w/discs , armored diff covers, 40" MTR's

05-03-2003, 01:46 PM	#13
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	Sent you e mail your pm box is full. __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.