clutch pivot on 400 sb - The 1947 - Present Chevrolet & GMC Truck Message Board Network

robby · 05-03-2003, 05:19 PM

I just checked out the motor in my 79 k20 that I am going to part out on the advice from a board member because I asssumed that I could put it in my 72 K10 with a four speed. Well lo and behold the block has a boss for the pivot but it is not drilled and tapped for it. Question is can I drill and tap it successfully or is it not worth the hassle? I need to find a flywheel for a 400 anyway. Maybe I should fix mine or find another 350 for my K10-Thoughts?

lpaine · 05-03-2003, 06:26 PM

You can drill and tap it, but it's a lot easier with the engine out- which I assume you're doing anyway. I'd say it would be a simple enough 2 or 3-beer-job.

Chevy Wrench · 05-03-2003, 07:40 PM

More than likely, you will end up drilling into the water jacket. If so, dont be alarmed, just make sure to seal the threads with a good sealant.

robby · 05-03-2003, 11:27 PM

so not a real high skill job? I will have it out of the truck.

spinning wheels · 05-04-2003, 12:31 AM

When I bought a 400 small block, (this was many years ago), to install in my 70 Z28. I found out that GM never installed a 400 small block with a stick. So, no flywheel was available. Since the motor is externally balanced, none of the other small block's flywheel would work, they are internally balanced. Hopefully you won't run into that problem. I mean, I hope you can find an aftermarket flywheel that won't set you back a whole bunch of bucks. I can't say that it has never been done, just not sure if its the best or most cost effective way to go.

JimKshortstep4x4 · 05-04-2003, 06:38 AM

I have a 400 small block installed in my 65 SS with a M 22. The bell housing that I am using has the clutch pivot tapped hole in it and for this application it works well.

Flywheels are available, I bought mine from Northern.

Jim

robby · 05-04-2003, 10:21 AM

I have another thread about the flywheel, basic consensus is that you can buy a flywheel for about $150 new. I think there are a few trucks in the 70's that might have had a manual tranny behind a 400. but I won't wear myself out looking for one. Thanks

robby · 05-04-2003, 12:36 PM

Just looked up the 400 flywheel in Norhtern's web site-$109.

05-03-2003, 05:19 PM	#1
robby Semper Fidelis Join Date: Dec 2001 Location: Cedar City, Utah Posts: 654	clutch pivot on 400 sb I just checked out the motor in my 79 k20 that I am going to part out on the advice from a board member because I asssumed that I could put it in my 72 K10 with a four speed. Well lo and behold the block has a boss for the pivot but it is not drilled and tapped for it. Question is can I drill and tap it successfully or is it not worth the hassle? I need to find a flywheel for a 400 anyway. Maybe I should fix mine or find another 350 for my K10-Thoughts? __________________ 72 Chevy C 20 with 402 For sale 85 GMC K2500 83 Trans Am Cedar City, Utah (Missouri Native)

05-03-2003, 06:26 PM	#2
lpaine Registered User Join Date: Oct 2002 Location: Parksville, B.C. Canada Posts: 637	You can drill and tap it, but it's a lot easier with the engine out- which I assume you're doing anyway. I'd say it would be a simple enough 2 or 3-beer-job. __________________ 1969 G.M.C 3/4 Ton 920 (Canadian Version) 307 3 speed, currently apart 1998 Chevy 1/2 ton ex cab V-6 5 speed 1967 Chevy SWB - project truck; not started just yet

05-03-2003, 07:40 PM	#3
Chevy Wrench former desert rat Join Date: Feb 2003 Location: salt lake city, utah Home of the 3 M's Mormons, methlabs and minivans Posts: 320	More than likely, you will end up drilling into the water jacket. If so, dont be alarmed, just make sure to seal the threads with a good sealant. __________________ 94 Chevy Silverado Ext cab 4/6 drop w/ 18's and 2500watt system (work truck). 67 Chevy swb under const. frame off custom, 20's, bagged and a large rat under the hood,and a 1940 Chevy truck under const.

05-03-2003, 11:27 PM	#4
robby Semper Fidelis Join Date: Dec 2001 Location: Cedar City, Utah Posts: 654	so not a real high skill job? I will have it out of the truck. __________________ 72 Chevy C 20 with 402 For sale 85 GMC K2500 83 Trans Am Cedar City, Utah (Missouri Native)

05-04-2003, 12:31 AM	#5
spinning wheels Registered User Join Date: Sep 2001 Location: Hacienda Heights, California USA Posts: 474	When I bought a 400 small block, (this was many years ago), to install in my 70 Z28. I found out that GM never installed a 400 small block with a stick. So, no flywheel was available. Since the motor is externally balanced, none of the other small block's flywheel would work, they are internally balanced. Hopefully you won't run into that problem. I mean, I hope you can find an aftermarket flywheel that won't set you back a whole bunch of bucks. I can't say that it has never been done, just not sure if its the best or most cost effective way to go. __________________ '72 GMC custom camper 350/350

05-04-2003, 06:38 AM	#6
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	I have a 400 small block installed in my 65 SS with a M 22. The bell housing that I am using has the clutch pivot tapped hole in it and for this application it works well. Flywheels are available, I bought mine from Northern. Jim

05-04-2003, 10:21 AM	#7
robby Semper Fidelis Join Date: Dec 2001 Location: Cedar City, Utah Posts: 654	I have another thread about the flywheel, basic consensus is that you can buy a flywheel for about $150 new. I think there are a few trucks in the 70's that might have had a manual tranny behind a 400. but I won't wear myself out looking for one. Thanks __________________ 72 Chevy C 20 with 402 For sale 85 GMC K2500 83 Trans Am Cedar City, Utah (Missouri Native)

05-04-2003, 12:36 PM	#8
robby Semper Fidelis Join Date: Dec 2001 Location: Cedar City, Utah Posts: 654	Just looked up the 400 flywheel in Norhtern's web site-$109. __________________ 72 Chevy C 20 with 402 For sale 85 GMC K2500 83 Trans Am Cedar City, Utah (Missouri Native)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.