What would you do? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Oklahoma · 02-23-2010, 03:39 PM

How would you replace the seal lip? would you use a strip of metal? or is there a piece that I can buy as a replacement? Thanks Guys

ClifBlazer · 02-23-2010, 03:53 PM

that strip is part of the kick panal blew and the floor panel above

**Chevy Fleetside** · 02-23-2010, 03:55 PM

http://www.truckandcarshop.com/trucks60_72/t60_068.html Bottom left had side.. Rocker panels.

JRBECK64 · 02-23-2010, 04:00 PM

Ive used a few different patch panels and I would suggest that you use the TRI PLUS patch panels. The reason I say that is because they tend to fit more to the Stock sheet metal than other that I have used. Im sure someone will disagree but that is what I have found to work the best for me. Take a close look at the sheet metal where it goes just past that Seal Strip in the cab, you might find that you need to replace the inside rocker as well. Good luck with your Project.

JRBECK64

SIR · 02-23-2010, 04:48 PM

wire brush that part get it clean and THEN decide what your going to do,if the rust isn't too bad just weld it up and grind it down....

ClifBlazer · 03-12-2010, 02:17 AM

you know thats right

02-23-2010, 03:39 PM	#1
Oklahoma Registered User Join Date: Oct 2008 Location: broken arrow oklahoma Posts: 266	What would you do? How would you replace the seal lip? would you use a strip of metal? or is there a piece that I can buy as a replacement? Thanks Guys Attached Images

02-23-2010, 03:53 PM	#2
ClifBlazer Registered User Join Date: Jul 2009 Location: Lee Summit ,MO. Posts: 160	Re: What would you do? that strip is part of the kick panal blew and the floor panel above

02-23-2010, 03:55 PM	#3
Chevy Fleetside Registered User Join Date: Sep 2006 Location: San Francisco Posts: 4,782	Re: What would you do? http://www.truckandcarshop.com/trucks60_72/t60_068.html Bottom left had side.. Rocker panels. __________________ "A man and his truck, what a beautiful thing" 65 Short Fleetside BBC 65 Long Fleetside 283 3 on the tree for now. my build thread http://www.67-72chevytrucks.com/vboa...d.php?t=259536

02-23-2010, 04:00 PM	#4
JRBECK64 Registered User Join Date: Sep 2008 Location: Cornelius Oregon Posts: 1,073	Re: What would you do? Ive used a few different patch panels and I would suggest that you use the TRI PLUS patch panels. The reason I say that is because they tend to fit more to the Stock sheet metal than other that I have used. Im sure someone will disagree but that is what I have found to work the best for me. Take a close look at the sheet metal where it goes just past that Seal Strip in the cab, you might find that you need to replace the inside rocker as well. Good luck with your Project. JRBECK64

02-23-2010, 04:48 PM	#5
SIR SIR Join Date: Apr 2005 Location: grants pass oregon,usa Posts: 658	Re: What would you do? wire brush that part get it clean and THEN decide what your going to do,if the rust isn't too bad just weld it up and grind it down.... __________________ 66long low fleet http://community.webshots.com/user/LVNR66

03-12-2010, 02:17 AM	#6
ClifBlazer Registered User Join Date: Jul 2009 Location: Lee Summit ,MO. Posts: 160	Re: What would you do? you know thats right

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.