1SIK69 build.... - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

VA72C10 · 04-10-2009, 11:09 PM

Looking good. Billet's gonna pop against all that black

*Puropedo* · 04-13-2009, 12:30 AM

Are you using 2.5 spindles? Do you get any rubbing with the lowers being cut? What drop did u get by cutting the lowers? Nice project!

barthmonster · 04-13-2009, 05:51 AM

you really do nice work. Can't wait to see the firewall... Wan't to show me how to shave mine ??

1SIK69 · 04-26-2009, 01:29 AM

Thanks for the compliments. I am learning as I go with the help of some good friends in my truck club. Well today we put a big dent in the truck. We installed the compressors, fuel cell, mounted a few other things and notched the cab for drive shaft clearance. We also repaired that rust hole in the windshield seal. Here are a few pics.

1SIK69 · 04-26-2009, 01:32 AM

Quote:

Originally Posted by Puropedo

Are you using 2.5 spindles? Do you get any rubbing with the lowers being cut? What drop did u get by cutting the lowers? Nice project!

I was told they were 3 inch spindles. Not for sure. I didn't get them new. as far as rubbing with the lowers being cut, not that I know of. I haven't driven it since I started the bag job. I will let you know, but I don't think so. As far as the drop from the lowers, I was told it would lay out on 22's. I have 20's on it and the lowers are laying on the ground.

OARNGESI · 04-26-2009, 07:55 AM

Itas looking really good

idonutn0 · 04-26-2009, 10:58 AM

How did you make the piece to fix the rust hole on the windshield corner?
Thanks

nuke1 · 04-26-2009, 02:18 PM

lookin darn good, those rear wheels just are sexy to look at with that width.

1SIK69 · 04-26-2009, 09:28 PM

Quote:

Originally Posted by idonutn0

How did you make the piece to fix the rust hole on the windshield corner?
Thanks

My buddy Eric took a piece of sheet metal and folded it in half to get the lip. Then he started shaping it in place. Make relieve cuts to get the curve and such and welded it in.

1SIK69C10 · 06-03-2010, 10:05 AM

I am back on here now with a new username. I didn't have the same email and couldn't get the password. I got the truck on the road and running finally. I actually sold it and just got it back after almost a year. lol
I will post up some pics later.

basemodel67 · 06-03-2010, 10:16 AM

Wecome back... Now get up some pics!

1SIK69C10 · 06-04-2010, 10:47 PM

Here are a few pics. I installed a phantom grille since pics were taken. I just got a set of rally wheels to throw on it til I can get some 20's or 22's. I am gonna install a chrome brake booster and chrome master cylinder soon. Do a tilt hood. Eventually I am gonna Z the frame. More pics to follow

oldblue1968chevy · 06-04-2010, 11:35 PM

that thing is sweet man! I didnt like the wheels wheres the rally wheel pic?

1SIK69C10 · 06-05-2010, 12:42 AM

Quote:

Originally Posted by oldblue1968chevy

that thing is sweet man! I didnt like the wheels wheres the rally wheel pic?

I just got the rallys. I need to paint them and buy some new center caps and rings, and get some new tires too. Then I will get them on.

04-10-2009, 11:09 PM	#51
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: 1SIK69 build.... Looking good. Billet's gonna pop against all that black __________________ Looking for a 67-72 swb or blazer project in or around VA.

04-13-2009, 12:30 AM	#52
Puropedo Account Suspended Join Date: Nov 2008 Location: Prunedale California Posts: 782	Re: 1SIK69 build.... Are you using 2.5 spindles? Do you get any rubbing with the lowers being cut? What drop did u get by cutting the lowers? Nice project!

04-13-2009, 05:51 AM	#53
barthmonster Registered User Join Date: Nov 2007 Location: Chamberlain, SD Posts: 183	Re: 1SIK69 build.... you really do nice work. Can't wait to see the firewall... Wan't to show me how to shave mine ??

04-26-2009, 01:29 AM	#54
1SIK69 Registered User Join Date: Feb 2009 Location: Killeen, TX Posts: 55	Re: 1SIK69 build.... Thanks for the compliments. I am learning as I go with the help of some good friends in my truck club. Well today we put a big dent in the truck. We installed the compressors, fuel cell, mounted a few other things and notched the cab for drive shaft clearance. We also repaired that rust hole in the windshield seal. Here are a few pics.

04-26-2009, 07:55 AM	#56
OARNGESI Registered User Join Date: Sep 2008 Location: CASA GRANDE AZ Posts: 4,276	Re: 1SIK69 build.... Itas looking really good __________________ 70 SWB STEPSIDE 70 BLAZER 09 challenger

04-26-2009, 10:58 AM	#57
idonutn0 Registered User Join Date: Dec 2008 Location: Cypress TX Posts: 126	Re: 1SIK69 build.... How did you make the piece to fix the rust hole on the windshield corner? Thanks

04-26-2009, 02:18 PM	#58
nuke1 Registered User Join Date: Jun 2007 Location: Saskatoon, Saskatchewan,: Posts: 2,901	Re: 1SIK69 build.... lookin darn good, those rear wheels just are sexy to look at with that width. __________________ James 1968 GMC "HAVOC" 1986 GMC "Frank" J.J.R.H. Design & Consulting My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300 A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238 1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361 Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390 Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100 1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587

06-03-2010, 10:05 AM	#60
1SIK69C10 Registered User Join Date: May 2010 Location: Converse, TX Posts: 3	Re: 1SIK69 build.... I am back on here now with a new username. I didn't have the same email and couldn't get the password. I got the truck on the road and running finally. I actually sold it and just got it back after almost a year. lol I will post up some pics later.

06-03-2010, 10:16 AM	#61
basemodel67 Factory Strippers Rule! Join Date: Mar 2009 Location: Shingle Springs, CA Posts: 707	Re: 1SIK69 build.... Wecome back... Now get up some pics! __________________ "Feast your eyes on a feast of smoke." 67 Chevy Short Fleet PLAN: LQ9, 4L60, D60 Looking for School Bus Gauges - Help me out!

06-04-2010, 10:47 PM	#62
1SIK69C10 Registered User Join Date: May 2010 Location: Converse, TX Posts: 3	Re: 1SIK69 build.... Here are a few pics. I installed a phantom grille since pics were taken. I just got a set of rally wheels to throw on it til I can get some 20's or 22's. I am gonna install a chrome brake booster and chrome master cylinder soon. Do a tilt hood. Eventually I am gonna Z the frame. More pics to follow

06-04-2010, 11:35 PM	#63
oldblue1968chevy Grandpa in the rustmobile... Join Date: Nov 2008 Location: Spokane WA/Viola TN Posts: 11,422	Re: 1SIK69 build.... that thing is sweet man! I didnt like the wheels wheres the rally wheel pic? __________________ John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.