Brake rod pictures for WEBBES - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Todd68Chevy** · 10-04-2010, 08:44 PM

Here is a picture of the part that connects the brake master cylinder rod to the brake pedal arm.

frednoah · 10-04-2010, 09:13 PM

and if you're looking to fab a rod, you need about a 1 ft long piece of 7/16-20 (if memory serves correct) threaded rod to screw into the long piece.

frednoah · 10-04-2010, 09:19 PM

I think mine ended up about 11 inches total length, and I used a grinder to taper the end that went into the master cylinder. Just make sure you get it centered in the bore so it doesn't bind. Once you get it adjusted, tighten down the jamb nut and drive.

**Todd68Chevy** · 10-04-2010, 09:31 PM

Sorry I did not explain better but WEBBES has a rod that came with a brake kit but it did not come with the pedal end so I was showing him the pedal end of the rod. Thanks for the information. Todd

frednoah · 10-04-2010, 09:42 PM

I had the exact opposite happen. My trucks PO had butchered the part that passes into the firewall, and had a 2 year old weld it back together crooked about an inch from where it passed through.

10-04-2010, 08:44 PM	#1
Todd68Chevy Senior Member Join Date: Oct 2009 Location: Shelburn Indiana Posts: 3,977	Brake rod pictures for WEBBES Here is a picture of the part that connects the brake master cylinder rod to the brake pedal arm. Attached Images __________________ Note: All parts I have for sale are also for sale locally. I currently own: 1940 Chevy Fire truck (project), 1946 Chevy truck (project), 1946 Chevy 1 Ton pick up, 1953 Chevy school bus (storage area), 1968 Chevy C10 (I have drove for 26 years), 1994 Chevy C2500 (daily driver), 2005 GMC crew cab K2500 (parts hauler) and more trucks for parts.

10-04-2010, 09:13 PM	#2
frednoah 86 Scottsdale Join Date: May 2010 Location: Mooresville NC Posts: 473	Re: Brake rod pictures for WEBBES and if you're looking to fab a rod, you need about a 1 ft long piece of 7/16-20 (if memory serves correct) threaded rod to screw into the long piece.

10-04-2010, 09:19 PM	#3
frednoah 86 Scottsdale Join Date: May 2010 Location: Mooresville NC Posts: 473	Re: Brake rod pictures for WEBBES I think mine ended up about 11 inches total length, and I used a grinder to taper the end that went into the master cylinder. Just make sure you get it centered in the bore so it doesn't bind. Once you get it adjusted, tighten down the jamb nut and drive.

10-04-2010, 09:31 PM	#4
Todd68Chevy Senior Member Join Date: Oct 2009 Location: Shelburn Indiana Posts: 3,977	Re: Brake rod pictures for WEBBES Sorry I did not explain better but WEBBES has a rod that came with a brake kit but it did not come with the pedal end so I was showing him the pedal end of the rod. Thanks for the information. Todd __________________ Note: All parts I have for sale are also for sale locally. I currently own: 1940 Chevy Fire truck (project), 1946 Chevy truck (project), 1946 Chevy 1 Ton pick up, 1953 Chevy school bus (storage area), 1968 Chevy C10 (I have drove for 26 years), 1994 Chevy C2500 (daily driver), 2005 GMC crew cab K2500 (parts hauler) and more trucks for parts.

10-04-2010, 09:42 PM	#5
frednoah 86 Scottsdale Join Date: May 2010 Location: Mooresville NC Posts: 473	Re: Brake rod pictures for WEBBES I had the exact opposite happen. My trucks PO had butchered the part that passes into the firewall, and had a 2 year old weld it back together crooked about an inch from where it passed through.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.