|
04-16-2009, 04:28 PM
|
#1 |
|
Registered User
Join Date: Feb 2008
Location: Jackson, TN
Posts: 99
|
door window seals
Has anyone used outside door window seals from a later model or another vehicle, on their 67-72 chevy truck? The available seals for these trucks are, for lack of a better word, crap. They don't seal.
|
|
|
|
04-16-2009, 05:06 PM
|
#2 |
|
Registered User
 
Join Date: Oct 2006
Location: Overton,Texas
Posts: 148
|
Re: door window seals
I agree, CRAPPY. they don't even come near the window. Would like to know a better option myself
__________________
Spanky 
|
|
|
|
|
12-06-2010, 02:00 PM
|
#3 |
|
Account Suspended
Join Date: Aug 2007
Location: USA
Posts: 1,223
|
Re: door window seals
anybody have any suggestions
|
|
|
|
|
12-06-2010, 02:27 PM
|
#4 |
|
Registered User
Join Date: Jul 2010
Location: central michigan
Posts: 1,194
|
Re: door window seals
also looking for a replacement
|
|
|
|
|
12-06-2010, 02:33 PM
|
#5 |
|
Big Red - Now its a SWB!
Join Date: Jun 2009
Location: Oroville, Ca
Posts: 1,624
|
Re: door window seals
Me too!
__________________
68 3/4 ton  (Project)-350 Small Block, .030 over, 10:1 comp, 3998993 heads, C3BX edelbrock intake, comp cams XE268, Holley 670 SA, long tube headers, dual flow 40's, E-fan, Alum rad, currently under the knife getting shortened and bagged  build thread41 3/4 ton (wife's)-flatbed, fully restored to original01 Tahoe LT 4WD (my daily driver)-Magnaflow Muffler, Rollin on 22's 02 Ford Mustang Convertable (Wife's Car)-Flowmaster 50, Clear corners, Intake, sittin on 18's |
|
|
|
|
12-06-2010, 02:36 PM
|
#6 |
|
Registered User
Join Date: Jul 2010
Location: dublin, ca
Posts: 155
|
Re: door window seals
hum... I just ordered come from LMC and they seem great...
|
|
|
|
|
12-06-2010, 02:43 PM
|
#7 |
|
Moderator
 
Join Date: May 2007
Location: Southern Cal
Posts: 20,031
|
Re: door window seals
Nos
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul |
|
|
|
|
12-07-2010, 12:01 AM
|
#8 |
|
Registered User
Join Date: Oct 2007
Location: Spanaway
Posts: 8,451
|
Re: door window seals
I have bought 2 sets one from LMC the other locally and nether were very good, they only touch the window when all the way up which is pretty much normal, but all of them are angled down and inward towards the glass so all the rain water just runs inside the door! Don't know why someone cant make a set that is long enough to stay in contact with the window and point upward so the water runs to the outside of the door, sigh..
__________________
Mike. Swamp Rat build thread : http://67-72chevytrucks.com/vboard/s...d.php?t=595019 72 3/4T 4X4 4" BDS Lift 33" BFG's |
|
|
|
|
12-07-2010, 10:36 AM
|
#9 |
|
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Re: door window seals
The truck doors can spread at the window seals. This is especially true when the brace on the 67-71 trucks breaks between the two door halves.
In 72 this problem was fixed when a screw was installed at the vent window to hold the inner and outer door panels together. You may want to check the opening between the two halves as a possible problem. Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC |
|
|
|
|
12-07-2010, 11:01 AM
|
#10 |
|
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: door window seals
Classic Heartbeat has some good ones, though I agree on the door separation issue.
__________________
Beat it to fit, Paint it to match... 
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
