Drop Sindle installation help......????? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

FILICE72C10 · 06-24-2003, 10:53 PM

When replacing my front spindles with 2 1/2drop spindles on my 72 C10 SWB, what other preventative maintainance should I do? I already bought the upper and lower ball joints, new shocks, and new rubber bumpers, anything else?

One other question, how hard is it to install the rear shock re-locaters? Do I have to drill out the top mounts and remount the new mounts? Can I do this with the bed on?

Any advice would be great!

thanks!

So you'll know what im working with..... Next weekend it will be 2 1/2 and 4 inches lower!

7T1BURB · 06-25-2003, 07:38 AM

The original upper shock mounts will have to be removed. I recently did this on our BURB (now with 2.5 dropped spindles in front and 4" dropped rear coils) and cut the rivets of the original rear shock mounts out with a high speed grinder wheel. After removing the rivet heads, I punched out the remaining part of the rivet(s). The ECE shock locators are then bolted to the frame...not a really difficult time and about an hours worth of grinding and cussing.....hope this helps! Good luck on your project.

cdowns · 06-25-2003, 12:24 PM

when i did my spindels i also changed the tierod ends and the swaybar bushings

**COBALT** · 06-25-2003, 12:53 PM

I used this opportunity to clean up the cross member, and replace my control arm center bars and bushings. Good thing to - there was one that had failed.

FILICE72C10 · 06-25-2003, 07:09 PM

Thanks for the advice!

phantom dually · 06-25-2003, 10:32 PM

Put new bearings in and check your brake rotors and pads.

FILICE72C10 · 06-25-2003, 11:23 PM

i just did new bearings, new front disks and pads about 6 months ago, so i should be solid, that does make perfect sense it I had not done it already

thanks

Slammed '87 · 07-08-2003, 09:22 PM

Hi, just wanted to say that is a nice ride!, can u post some pic's of it lowered?

FILICE72C10 · 07-08-2003, 10:28 PM

here are some pics

http://67-72chevytrucks.com/vboard/s...threadid=58677

06-24-2003, 10:53 PM	#1
FILICE72C10 Registered User Join Date: Dec 2002 Location: San Francisco, CA Posts: 270	Drop Sindle installation help......????? When replacing my front spindles with 2 1/2drop spindles on my 72 C10 SWB, what other preventative maintainance should I do? I already bought the upper and lower ball joints, new shocks, and new rubber bumpers, anything else? One other question, how hard is it to install the rear shock re-locaters? Do I have to drill out the top mounts and remount the new mounts? Can I do this with the bed on? Any advice would be great! thanks! So you'll know what im working with..... Next weekend it will be 2 1/2 and 4 inches lower! Attached Images __________________ 72 C10 SWB 02 Subaru WRX 95 Nissan 240SX

06-25-2003, 12:24 PM	#3
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	when i did my spindels i also changed the tierod ends and the swaybar bushings __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

06-25-2003, 12:53 PM	#4
COBALT Senior Member Join Date: Sep 2001 Location: Seattle, WA, USA Posts: 5,817	I used this opportunity to clean up the cross member, and replace my control arm center bars and bushings. Good thing to - there was one that had failed. __________________ '69 3/4 ton C20 2wd-350ci/TH400 '69 3/4 ton Custom 20 2wd-350ci/4sp Manual '99 2wd 5.7 Chevy Tahoe Seattle, WA.

06-25-2003, 07:09 PM	#5
FILICE72C10 Registered User Join Date: Dec 2002 Location: San Francisco, CA Posts: 270	Thanks for the advice! __________________ 72 C10 SWB 02 Subaru WRX 95 Nissan 240SX

06-25-2003, 10:32 PM	#6
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,793	Put new bearings in and check your brake rotors and pads. __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

06-25-2003, 07:38 AM	#2
7T1BURB Registered User Join Date: Aug 2002 Location: Newport News, VA Posts: 190	The original upper shock mounts will have to be removed. I recently did this on our BURB (now with 2.5 dropped spindles in front and 4" dropped rear coils) and cut the rivets of the original rear shock mounts out with a high speed grinder wheel. After removing the rivet heads, I punched out the remaining part of the rivet(s). The ECE shock locators are then bolted to the frame...not a really difficult time and about an hours worth of grinding and cussing.....hope this helps! Good luck on your project.

06-25-2003, 11:23 PM	#7
FILICE72C10 Registered User Join Date: Dec 2002 Location: San Francisco, CA Posts: 270	i just did new bearings, new front disks and pads about 6 months ago, so i should be solid, that does make perfect sense it I had not done it already thanks __________________ 72 C10 SWB 02 Subaru WRX 95 Nissan 240SX

07-08-2003, 09:22 PM	#8
Slammed '87 Registered User Join Date: Feb 2003 Location: Calgary Canada Posts: 556	SWEET Hi, just wanted to say that is a nice ride!, can u post some pic's of it lowered?

07-08-2003, 10:28 PM	#9
FILICE72C10 Registered User Join Date: Dec 2002 Location: San Francisco, CA Posts: 270	. here are some pics http://67-72chevytrucks.com/vboard/s...threadid=58677 __________________ 72 C10 SWB 02 Subaru WRX 95 Nissan 240SX

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.