![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Feb 2010
Location: carthage missouri
Posts: 81
|
84 c10 power window problems
Hey guys as stated having some issues with my windows..... They won't go up or down! Replaced the circuit breaker and srill nothing. Is It likely that both switches would go out? Pls help lol
Posted via Mobile Device |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jun 2010
Location: Tyndall AFB FL
Posts: 214
|
Re: 84 c10 power window problems
i am having some of the same issues, on my driver side switched i can roll both windows up and down but on the passenger side switch will only allow me to roll the window up not down any suggestions for me?
__________________
84 Short bed 350: Hooker headers, flow master 40 series, edelbrock Intake manifold, Holly street avenger carb, 4 inch skyjacker suspension lift, 33x12.5 Toyo Open Country Mud Terrains, 3.73 gears ![]() 2011 Silverado LTZ |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Feb 2010
Location: carthage missouri
Posts: 81
|
Re: 84 c10 power window problems
Ya neither of my switches will move either window kinda ****ty especially since Itd warming up
Posted via Mobile Device |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Mar 2003
Location: wichita falls tx
Posts: 429
|
Re: 84 c10 power window problems
More than likely you lost power to the driver side switch. If I remember correctly power for both windows enter the dvr. door. Your switch on the pass. side gets power from the pass. switch on the dvr. side door. So if you lose that main feed on the dvr. side both windows wont work. Pull the switch on the dvr. side and see if you have 12V at any of the pins. If not, trace your wire from your circuit breaker to the switch. Not likely both switches would go out at the same time, but anythings possible!
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jul 2007
Location: Tucson, AZ
Posts: 3,188
|
Re: 84 c10 power window problems
For power window problems, pull the switch away from the door panel, operate the switch while wiggling the wires on the connector behind the switch. Push/pull lightly on the wires where they enter the connector. If the switch works intermittently, then I suspect this connector/harness. The generic harness is still available from AC/Delco (PT254). In my experience, a lot of switches and motors were replaced when it was really the harness that was the problem.
|
![]() |
![]() |
![]() |
#6 |
78K & 79C Jimmys
Join Date: Nov 2009
Location: Ottawa Ont CANADA
Posts: 7,901
|
Re: 84 c10 power window problems
i've found the wire breaks in that black tube in the door jam
there is a harness/plugin under the edge of the dash for the door
__________________
John 1978 GMCJimmy4X4-350/203 1979 GMCJimmy4X2-305/350 |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Mar 2003
Location: wichita falls tx
Posts: 429
|
Re: 84 c10 power window problems
Yeah, but it might be better to just take the fender off next time you are trying to access the jam
![]() |
![]() |
![]() |
![]() |
#8 |
78K & 79C Jimmys
Join Date: Nov 2009
Location: Ottawa Ont CANADA
Posts: 7,901
|
Re: 84 c10 power window problems
what can i say......
Apparently excessive alcohol was used to find the proper location.... and the window motor still won't work,but now i know where it's broke lol
__________________
John 1978 GMCJimmy4X4-350/203 1979 GMCJimmy4X2-305/350 |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|