Power steering pump brackets question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Fesser · 03-19-2011, 08:18 PM

Is there any difference on power steering pump brackets on two wheel drives and four wheel drives. I have two setups here that I believe are first gen. smallblock setups. One is cast and seems more compact, the other is cast and stamped. Just want to be sure either can be used on a k5.

gcburdic · 03-23-2011, 12:17 PM

ttt

Fesser · 03-23-2011, 05:53 PM

May have answered my own question. I tried both types on the Blazer and they both seem to clear everything.

JimKshortstep4x4 · 03-23-2011, 07:21 PM

They both will work. The pulley location may be different between the two setups so check it out. The all cast brackets go with the cast crank pulleys.

Jim

Tx Firefighter · 03-23-2011, 08:52 PM

I've seen more than a few of the steel ones crack but never a cast one. I've been told by my buddy, GM guru and long time Chevy dealer parts guy, that this was a running change made to alleviate the cracking issue.

03-19-2011, 08:18 PM	#1
Fesser Registered User Join Date: Feb 2010 Location: Napa, CA Posts: 519	Power steering pump brackets question Is there any difference on power steering pump brackets on two wheel drives and four wheel drives. I have two setups here that I believe are first gen. smallblock setups. One is cast and seems more compact, the other is cast and stamped. Just want to be sure either can be used on a k5.

03-23-2011, 12:17 PM	#2
gcburdic Restoration Virgin! Join Date: Jan 2008 Location: Huntersville, NC Posts: 8,298	Re: Power steering pump brackets question ttt __________________ Geoff with a G 1968 Chevy C10 SWB The Mistress 1972 Custom Deluxe C20 Suburban A Suburban Named Isabella 1966 Ford Mustang Mama's High School Graduation Present

03-23-2011, 05:53 PM	#3
Fesser Registered User Join Date: Feb 2010 Location: Napa, CA Posts: 519	Re: Power steering pump brackets question May have answered my own question. I tried both types on the Blazer and they both seem to clear everything.

03-23-2011, 07:21 PM	#4
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: Power steering pump brackets question They both will work. The pulley location may be different between the two setups so check it out. The all cast brackets go with the cast crank pulleys. Jim __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

03-23-2011, 08:52 PM	#5
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Power steering pump brackets question I've seen more than a few of the steel ones crack but never a cast one. I've been told by my buddy, GM guru and long time Chevy dealer parts guy, that this was a running change made to alleviate the cracking issue. __________________ I'm on the Instagram- @Gearhead_Kevin

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.