|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-14-2011, 08:17 PM
|
#1 |
|
Registered User
Join Date: Nov 2008
Location: midland,tx
Posts: 90
|
Truck bucks hard when put in reverse
Like the title says , everytime I put the truck in reverse it bucks pretty hard ....and the previous owner said he put a shift kit in... But I doubt that's the reason ....so please give me some advice
Posted via Mobile Device |
|
|
|
02-14-2011, 09:00 PM
|
#2 | |
|
just can't cover up my redneck
Join Date: May 2004
Location: Columbus OH
Posts: 11,414
|
Re: Truck bucks hard when put in reverse
most likely it is something loose in the drivetrain. A worn u-joint, slip joint or execssive slop on the ring and pinions gears can all cause the clunking/banging.....a high idle speed can make it even worse.
__________________
You can review the site's rules here. Quote:
Bad planning on your part does not necessarily constitute an instant emergency on my part.... The great thing about being a pessimist is that you are either pleasantly surprised or right. 
|
|
|
|
|
|
02-14-2011, 10:06 PM
|
#3 |
|
Registered User
Join Date: Dec 2009
Location: Snohomish, Washington
Posts: 1,187
|
Re: Truck bucks hard when put in reverse
x2 on what Longhair said..
However, I had a similar problem with my truck when I would pop it into reverse. It was bad, the entire truck twisted. Turns out my shocks were bad. Replaced them with the new drop shocks and everything was normal. |
|
|
|
|
02-15-2011, 03:40 AM
|
#4 |
|
Registered User
Join Date: Jan 2010
Location: livermore ca
Posts: 114
|
Re: Truck bucks hard when put in reverse
i have a shift kit in my turbo 400 and mine bucks hard when truck is cold otherwise its bucks but no to bad...
|
|
|
|
|
02-15-2011, 05:12 AM
|
#5 |
|
Registered User
Join Date: May 2007
Location: The Netherlands
Posts: 185
|
Re: Truck bucks hard when put in reverse
Mine bucks very hard.....but only into Drive.....
__________________
1972 GMC 2500 Sierra 350 1971 Pontiac LeMans Sport 400 GTO/Judge Clone 1970 Pontiac GTO 400 convertible restoproject 1970 Pontiac Bonneville 455 convertible |
|
|
|
|
04-06-2011, 10:01 PM
|
#6 |
|
Registered User
Join Date: Mar 2011
Location: Dallas, Texas
Posts: 920
|
Re: Truck bucks hard when put in reverse
Mine bucks very hard when put into gear period, but I've got slop in every single piece of my drivetrain, so...Lol.
__________________
1955 Chevy 3600 http://67-72chevytrucks.com/vboard/s...61#post8589061 |
|
|
|
|
04-06-2011, 10:17 PM
|
#7 |
|
Registered User
Join Date: Aug 2010
Location: Virginia Beach, VA
Posts: 64
|
Re: Truck bucks hard when put in reverse
check the rear tranny mount
|
|
|
|
|
04-06-2011, 10:26 PM
|
#8 | |
|
oldschoolblazer@yahoo.com
Join Date: Jun 2007
Location: Long Beach CA.
Posts: 1,968
|
Re: Truck bucks hard when put in reverse
Quote:
also maybe even a motor mount ? Last edited by JOHNORO; 04-06-2011 at 10:29 PM. Reason: sp |
|
|
|
|
|
04-07-2011, 12:44 AM
|
#9 |
|
Registered User
Join Date: Sep 2010
Location: The Dalles, OR
Posts: 392
|
Re: Truck bucks hard when put in reverse
mine was slamming into reverse pretty hard too after a shift kit uprgrade. Seemed to run fine besides that. Forward gears engaged a little harder but nothing like the reverse.
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
