Whats the procedure for cutting front springs.. - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

oldblue1968chevy · 07-25-2010, 09:59 PM

Cool keep us updated! Is he gonna try to run a trac bar or make one?

Camaro_nut2001 · 07-31-2010, 01:34 PM

I'm not sure. I was suppose to go up and visit him today in my '69 but it's raining. I may drive something else and head up anyway. I will let you know. Ted

Dano69c10 · 05-26-2011, 05:57 PM

Instead of cutting one coil from the bottom, would it be better to cut half a coil from the top and half a coil from the bottom?

**lolife99** · 05-26-2011, 09:29 PM

Quote:

Originally Posted by Dano69c10

Instead of cutting one coil from the bottom, would it be better to cut half a coil from the top and half a coil from the bottom?

No.
The bottom (only) can be cut.
The top has a smaller pigtail end that fits up in the crossmember, and matches up to a "D" shaped piece of steel.
When you have the spring out,... look up in the spring pocket and you will see it.

richards72chevy · 05-26-2011, 11:11 PM

I chopped the coils on my impala and iwas told to put the cut ends up top.Big mistake!One side worked its way up into a little opening in the frame and that side wouldnt move.I had to take it apart took me about two days to pull that spring out of there.

**N2TRUX** · 05-26-2011, 11:41 PM

Just an FYI for anyone considering cutting a coil spring. There are several ways to cut them, and as mentioned always avoid excessive heat. I have used many of the methods mentioned. One that wasn't mentioned is a "tile" blade in a circular saw. A tile blade is essentially a thin abrasive disc like those used in a cut-off tool. This is larger and made with the correct style arbor so it fits properly in a circular saw. If you don't have anything else to do the job, that old Black and Decker or Skill saw will work just fine.

chuckmc8 · 05-27-2011, 06:21 AM

I used a cut-off wheel in my 4 1/2" side grinder to cut mine. (brand name--METABO 'original slicer' is the deal!) Here is a photo for reference, it has 1/2 coil removed and 2 1/2" drop spindle. 5" drop springs on the rear.
I did this suspension mod during the build and then it went to the alignment shop, had it aligned, all was good...

**70cst** · 05-27-2011, 07:43 AM

Quote:

Originally Posted by lolife99

No.
The bottom (only) can be cut.
The top has a smaller pigtail end that fits up in the crossmember, and matches up to a "D" shaped piece of steel.
When you have the spring out,... look up in the spring pocket and you will see it.

lolife99 speaks truth.

AustinScott · 05-27-2011, 10:17 PM

here is my thread with pics...

Front coil cut thread!

50bomb · 05-29-2011, 09:57 PM

Quote:

Originally Posted by Hubscrub

the more i think about it i would like to lower mine but i'm gonna wait. i need so much other stuff

i want to make it comfortable first and really i just wanna put some miles on it. Have you been looking for a cab any?

Leave that stance alone..Geez..it does look good the way it is. Go swimming already so you wont hack the poor thing anymore than it is!

J/K!!!!!

07-25-2010, 09:59 PM	#26
oldblue1968chevy Grandpa in the rustmobile... Join Date: Nov 2008 Location: Spokane WA/Viola TN Posts: 11,422	Re: Whats the procedure for cutting front springs.. Cool keep us updated! Is he gonna try to run a trac bar or make one? __________________ John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4

07-31-2010, 01:34 PM	#27
Camaro_nut2001 Chevy Lover Till The End. Join Date: Dec 2009 Location: Mascot TN. Posts: 795	Re: Whats the procedure for cutting front springs.. I'm not sure. I was suppose to go up and visit him today in my '69 but it's raining. I may drive something else and head up anyway. I will let you know. Ted __________________ 1969 Chevy SWB Big Block - Under the knife as of 12/26/2011 1989 Chevy Silverado, 4X4 - Daily Driver 1996 Chevy Suburban K1500 - 4-Wheeler, Campin Truck 1968 Chevrolet Impala Sport Coupe - 327/350hp, TH400, all original. Members I've met: BamaBaxter, My Build: http://67-72chevytrucks.com/vboard/s...d.php?t=500359

05-26-2011, 05:57 PM	#28
Dano69c10 Senior Member Join Date: Jan 2005 Location: Ontario, Kali Posts: 2,427	Re: Whats the procedure for cutting front springs.. Instead of cutting one coil from the bottom, would it be better to cut half a coil from the top and half a coil from the bottom? __________________ '69 Fleet It ain't yours, if you didn't build it!

05-26-2011, 11:11 PM	#30
richards72chevy Registered User Join Date: Dec 2010 Location: konawa ok/oakdale Ca. Posts: 1,652	Re: Whats the procedure for cutting front springs.. I chopped the coils on my impala and iwas told to put the cut ends up top.Big mistake!One side worked its way up into a little opening in the frame and that side wouldnt move.I had to take it apart took me about two days to pull that spring out of there.

05-26-2011, 11:41 PM	#31
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: Whats the procedure for cutting front springs.. Just an FYI for anyone considering cutting a coil spring. There are several ways to cut them, and as mentioned always avoid excessive heat. I have used many of the methods mentioned. One that wasn't mentioned is a "tile" blade in a circular saw. A tile blade is essentially a thin abrasive disc like those used in a cut-off tool. This is larger and made with the correct style arbor so it fits properly in a circular saw. If you don't have anything else to do the job, that old Black and Decker or Skill saw will work just fine. __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

05-27-2011, 06:21 AM	#32
chuckmc8 It's alsways something..... Join Date: Nov 2008 Location: Douglasville GA Posts: 1,171	Re: Whats the procedure for cutting front springs.. I used a cut-off wheel in my 4 1/2" side grinder to cut mine. (brand name--METABO 'original slicer' is the deal!) Here is a photo for reference, it has 1/2 coil removed and 2 1/2" drop spindle. 5" drop springs on the rear. I did this suspension mod during the build and then it went to the alignment shop, had it aligned, all was good... Attached Images __________________ 1968 RS Camaro 'Vert Matching number 327 and M21 Muncie 1968 C10 Black with red interior and orig paint. 5.3 / 4l60e,3:73 POSI 17" Torq Thrusts 1968 CST 514 Red with black interior. Buddy Buckets, Factory A/C, PS, PB- 20" AR custom shop TT, 5.3 and 4l60e Last edited by chuckmc8; 05-27-2011 at 10:53 AM.

05-27-2011, 10:17 PM	#34
AustinScott Registered User Join Date: Dec 2007 Location: Southington CT Posts: 548	Re: Whats the procedure for cutting front springs.. here is my thread with pics... Front coil cut thread!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.