1 Ton Front Fender Emblems - The 1947 - Present Chevrolet & GMC Truck Message Board Network

6600DURAMAX · 09-02-2011, 10:43 PM

What are you guys using for your 1 ton 4x4 front fender emblems

Everyone keeps asking why my "custom 10" has a dana 60

i should have put them on when I did the build since they would have been super easy to change, hopefully I can reach them from the underside without removing the fenders

Chevy1TonFun · 09-03-2011, 06:02 PM

You could use the Custom/20 emblems.

**special-K** · 09-04-2011, 07:29 AM

Why not put a pair of Custom/30s on? I had a Custom Deluxe that I did that with. I found a pair of Cheyenne/30s. Those are the hard ones. The hardest are GMC Sierra Grande 3500s. That's what I'm on the lookout for now

Burt4x4 · 09-05-2011, 12:09 PM

Quote:

Originally Posted by special-K

Why not put a pair of Custom/30s on? I had a Custom Deluxe that I did that with. I found a pair of Cheyenne/30s. Those are the hard ones. The hardest are GMC Sierra Grande 3500s. That's what I'm on the lookout for now

I agree..get a 30 on there.

6600DURAMAX · 09-06-2011, 08:46 AM

Yup, would definatley go with some 30's. Where is a good place to get these, I didn't see them on the Brothers site

Most of these emblems have speed nuts on the back correct? I reached in there yesterday and there are no nuts on the back side. Might be kind of hard to get these off.

**special-K** · 09-06-2011, 10:26 AM

Custom/30s aren't reproduced. Most 1 tons were Custom/30s so there should be plenty around. Check pic-a-parts and the parts section here. They are fastened with speed nuts. Yours may be glued on. People can be lazy like that.

Big-Blue · 09-10-2011, 11:26 PM

I have an ugly pair you can have. They were off a 69 that was owned by a fire dept. I think one had been drilled through the face and was held on by rivets. I can post pics if you want. Not sure how you could put the studs back on as they are pot metal. Can you weld that stuff? Let me know if you want pics.
Posted via Mobile Device

6600DURAMAX · 09-11-2011, 07:43 PM

Thanks for the offer Big Blue but I will pass. thanks again

09-02-2011, 10:43 PM	#1
6600DURAMAX Registered User Join Date: Nov 2000 Location: Wheatfield IN, USA Posts: 1,124	1 Ton Front Fender Emblems What are you guys using for your 1 ton 4x4 front fender emblems Everyone keeps asking why my "custom 10" has a dana 60 i should have put them on when I did the build since they would have been super easy to change, hopefully I can reach them from the underside without removing the fenders Attached Images __________________ 1972 K5 - LS3/408 (595Hp) -6L80e-One Tons with 4.56, 20'' Beadlocks with 37'' rubber, full TMI interior, JL Audio ..... 1971 CREWMAX Build.....at body shop for couple more years

09-03-2011, 06:02 PM	#2
Chevy1TonFun Grease Monkey Join Date: Oct 2007 Location: Fresno CA Posts: 750	Re: 1 Ton Front Fender Emblems You could use the Custom/20 emblems. __________________ Tow Rig: 2012 Chevy 2500HD CCSB LTZ Z71 4x4 Duramax Ultimate Offroad Build: 1978 Chevy Silverado K30 Crewcab Build Link http://67-72chevytrucks.com/vboard/s...d.php?t=654053 Mud Truck: 1972 Chevy Cheyenne K30 4x4, 468/400/205, D60/D70HD, 18" Custom Lift, 17x39" IROKs FOR SALE http://67-72chevytrucks.com/vboard/c...ton-4x4&cat=12

09-04-2011, 07:29 AM	#3
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: 1 Ton Front Fender Emblems Why not put a pair of Custom/30s on? I had a Custom Deluxe that I did that with. I found a pair of Cheyenne/30s. Those are the hard ones. The hardest are GMC Sierra Grande 3500s. That's what I'm on the lookout for now __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

09-06-2011, 08:46 AM	#5
6600DURAMAX Registered User Join Date: Nov 2000 Location: Wheatfield IN, USA Posts: 1,124	Re: 1 Ton Front Fender Emblems Yup, would definatley go with some 30's. Where is a good place to get these, I didn't see them on the Brothers site Most of these emblems have speed nuts on the back correct? I reached in there yesterday and there are no nuts on the back side. Might be kind of hard to get these off. __________________ 1972 K5 - LS3/408 (595Hp) -6L80e-One Tons with 4.56, 20'' Beadlocks with 37'' rubber, full TMI interior, JL Audio ..... 1971 CREWMAX Build.....at body shop for couple more years

09-06-2011, 10:26 AM	#6
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: 1 Ton Front Fender Emblems Custom/30s aren't reproduced. Most 1 tons were Custom/30s so there should be plenty around. Check pic-a-parts and the parts section here. They are fastened with speed nuts. Yours may be glued on. People can be lazy like that. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

09-10-2011, 11:26 PM	#7
Big-Blue Registered User Join Date: Dec 2008 Location: highland village, TX Posts: 309	Re: 1 Ton Front Fender Emblems I have an ugly pair you can have. They were off a 69 that was owned by a fire dept. I think one had been drilled through the face and was held on by rivets. I can post pics if you want. Not sure how you could put the studs back on as they are pot metal. Can you weld that stuff? Let me know if you want pics. Posted via Mobile Device

09-11-2011, 07:43 PM	#8
6600DURAMAX Registered User Join Date: Nov 2000 Location: Wheatfield IN, USA Posts: 1,124	Re: 1 Ton Front Fender Emblems Thanks for the offer Big Blue but I will pass. thanks again __________________ 1972 K5 - LS3/408 (595Hp) -6L80e-One Tons with 4.56, 20'' Beadlocks with 37'' rubber, full TMI interior, JL Audio ..... 1971 CREWMAX Build.....at body shop for couple more years

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.