![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#26 |
laying low
![]() Join Date: Mar 2001
Location: Searcy, Ark. USA
Posts: 13,266
|
Re: Has anybody out there cut coils or heated them for a drop?
wow diggin up an old thread here from 2009.
Still relevant today however. Some use Chevelle, Cultass or Skylark rear springs to drop a few inches. Being a smaller diameter wire they will ride good but not have the load carrrying capacity as a thicker truck spring. Some also use jeep springs. Same applies to them. It's all in how you intend to use your truck as to what springs to use I guess.
__________________
Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross |
![]() |
![]() |
![]() |
#27 |
Registered User
Join Date: Jul 2011
Location: strausstown pa
Posts: 3,394
|
Re: Has anybody out there cut coils or heated them for a drop?
I heard of the jeep springs but havent heard anything on the chevelle coils,I'm gonna hafta give it a try then. I wont be loading up my stepper I have a dd for that. but thanks for the info,boog
__________________
81 camaro 355 4/spd 342 posi my first love ![]() 67 swb step 454/4spd ott 373 posi 4/7 drop. 2000 s10 zr2 little blue truck that never gets stuck. '74 heald super bronc vt8. tecumseh powered moon rover. |
![]() |
![]() |
![]() |
#28 |
Grandpa in the rustmobile...
Join Date: Nov 2008
Location: Spokane WA/Viola TN
Posts: 11,422
|
Re: Has anybody out there cut coils or heated them for a drop?
jeep springs and chevelle springs are just too soft you can stand in t he bed and its on bumpstops.
(I ended up cutting my front springs 1 coil=2" drop heard not to cut more than 1 round) and put a 2" drop block in the rear total drop-2/2 1st pic truck springs/jeep tj rear springs 2nd pic cut front 1 round 2" drop block/stock truck springs
__________________
John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4 |
![]() |
![]() |
![]() |
#29 |
Registered User
Join Date: Dec 2008
Location: melbourne. AUSTRALIA
Posts: 110
|
Re: Has anybody out there cut coils or heated them for a drop?
The only problem I had after cutting 1 1/2 coils , was every time you jack the front up it's a pain in the butt coz the coils drop out of the pockets , so you've gotta hold it back in place as you lower the truck down ( carefully or ya could lose a finger or two ) ....
__________________
69 C10 350/350 flat bed 51 stepside LT1 350/t700r 88 C4 Corvette targa 350/t700r 65 C15 longbed |
![]() |
![]() |
![]() |
#30 |
Grandpa in the rustmobile...
Join Date: Nov 2008
Location: Spokane WA/Viola TN
Posts: 11,422
|
Re: Has anybody out there cut coils or heated them for a drop?
Yeah, mine does that too with 1 coil cut.
__________________
John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4 |
![]() |
![]() |
![]() |
#31 |
Grandpa in the rustmobile...
Join Date: Nov 2008
Location: Spokane WA/Viola TN
Posts: 11,422
|
Re: Has anybody out there cut coils or heated them for a drop?
better shot i think the 1st pic is a before
__________________
John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4 |
![]() |
![]() |
![]() |
#32 |
Registered User
Join Date: Feb 2011
Location: S.L.C.
Posts: 227
|
Re: Has anybody out there cut coils or heated them for a drop?
if i remember right (done 4 years ago) 2 coils up front and an axel flip out back
__________________
Im stright up ESL student........ ![]() 94 s10 4x4 4.3/5speed (dd) 68 lwb GMC 350/4speed 52 5 window GMC I6/4speed 12v (8lugs and long bed) 53 bel air 235 I6/powerglide |
![]() |
![]() |
![]() |
#33 |
Registered User
Join Date: Aug 2010
Location: Harrison Arkansas
Posts: 164
|
Re: Has anybody out there cut coils or heated them for a drop?
Although I don't think it's the best way to do it I have torched a few springs over the years. I did my wife's '76 last week. Dropped about three inches, it still has a nice ride.
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|