TX 5.3/4L60E complete setup for square body

[Jonboy]

I have decided to go ahead and sell the 5.3/4L60 combo I had put together for my '74. I have a 5.3 w/DBW throttle body from a 2001 Yukon. The truck had about 96K on it when it was wrecked. It looked clean under the valve covers and in the oil pan when it was pulled (the yard sucked the fluids from it before I got it). I have a 4L60E with 0 miles on it to go with it- the trans was gone through by the guys in the service shop wher eI work (Chevy dealership). I have put a CTS-V oil pan on it, with the correct pickup, windage tray, etc. as well. I have a resealed P/S pump, Dirty Dingo mounts, a new harness from www.fuelinjectionconnection.com (Robert flashed the PCM for me and tested the pedal and TAC module also), Kwik Performance high mount A/C bracket with a Sanden compressor and associated idler pulley, new in-tank Delco fuel pump, Delco spark plugs, wires, 2003 Silverado SS 3 piee engine covers (new), and a 1991 Suburban cluster modded with a GM sports Salvage tach/fuel gauge. I have almost everything that would be needed to drop this into a square body. Looking for $3500 for everything, and I really don't want to ship. There is probably a lot I have forgotten, but this is pretty much a complete package.

I am in the DFW area (Richardson is on the north side). Local pickup would probably be the best idea.

[Jonboy]

Anyone?

[LEEVON]

PM 67Cheby, he's looking. I would snatch this up if the timing was better.

[gearheads78]

Whatcha' doing instead?

[Jonboy]

Paying off bills and having a baby. It sucks growing up.

[gearheads78]

That sucks and contrats at the same time. My twins are now 17 months so I am finally seeing a light at the end of the tunnel on my doc bills. If you want a cheap project with lots of family room I still have the green Cutlass wagon. HAHA

[Jonboy]

You're killing me with the wagon. I still need it just as badly as I did last year. It is pretty rust free, right?

[gearheads78]

Original paint car no rust in main body. Needs rh front floor pan and a little patch work on the left floor. Only other rust in the car is the core support under the battery. I pulled the motor out of it to see why it was smoking and found the block was cracked from someone leaving just water in it. I picked up another 350 Olds motor that was running good when pulled but its still sitting on a stand. If you you are serious I'll take $2500.00 for everything or if you don't want the original torque thrusts or the motor we can work something out.
Would also consider trade on a good TIG

[Jonboy]

That's tempting. I have been looking for a home for this since it doesn't seem to be moving. Looking at Grand Wagoneers and Blazers (I have a 2wd Blazer chassis too) as well. I just don't want a money pit. Bad thing is, pretty much everything I like is a money pit. Such is life, I guess.

[gearheads78]

If you decide you are interested I would knock off $200.00 without the motor and $400.00 less the wheels. I would not take much to get it on the road. It was a daily driver 3 years ago. Been sitting inside my shop the last 2
I'll even deliver free in a 50 mile radius

[ramz]

Originally Posted by gearheads78

That sucks and contrats at the same time. My twins are now 17 months so I am finally seeing a light at the end of the tunnel on my doc bills. If you want a cheap project with lots of family room I still have the green Cutlass wagon. HAHA

Did that wagon have a 350 in it? My friends parents had one ... if I remember it was green and his dad put a 350 in it.
Got a pic?

[gearheads78]

Originally Posted by ramz

Did that wagon have a 350 in it? My friends parents had one ... if I remember it was green and his dad put a 350 in it.
Got a pic?

Car was in the Irving area when I found it.

[ramz]

No thats not it. Nice looking wagon

[PAWS 72]

Nice wagon. and your not running it. Wife would hang me if I brought that home. she would have to though. Love it. Jason

[Jonboy]

Any interest in this? I still have the original oil pan, so it could be sold without the CTS-V pan and without the gauges (priced accordingly) as well. It would save me having to buy a project to put it in!!!

[solidaxel]

Are you interested in parting out the aftermarket parts as I already have the engine and trans?

[Jonboy]

I actually sold the aftermarket stuff locally. Sorry.