|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
08-26-2013, 01:46 PM
|
#1 |
|
Registered User
Join Date: Aug 2012
Location: Neskowin OR
Posts: 1,153
|
Lower control arm question
I put new shafts in my lower control arms, and was wondering if the machined part to locate the u-bolts goes in the front or the back? I can't seem to find a picture that shows it. Any help would be appreciated, thanks!
|
|
|
|
08-26-2013, 02:31 PM
|
#2 |
|
Registered User
Join Date: Aug 2012
Location: Neskowin OR
Posts: 1,153
|
Re: Lower control arm question
 I found this and it answered my question, posted this just in case it can help someone else. |
|
|
|
|
08-26-2013, 03:28 PM
|
#3 |
|
Registered User
Join Date: Oct 2012
Location: Arlington Washington
Posts: 1,808
|
Re: Lower control arm question
The dimples go towards the rear of the truck
Posted via Mobile Device
__________________
Scott 67 c10 sold 89 c1500 90 k2500 91 s10 #chevyonly 
|
|
|
|
|
08-26-2013, 03:34 PM
|
#4 | |
|
Registered User
 
Join Date: Apr 2013
Location: Gainesville, TEXAS
Posts: 658
|
Re: Lower control arm question
No the dimples on the shafts go to the front, look at the pictures of the assembled lower control arms. (in the earlier post)
Note the orientation of the dimples on the shafts to the shock mounts. They are opposite each other. Quote:
|
|
|
|
|
|
08-26-2013, 03:43 PM
|
#5 |
|
Registered User
Join Date: Oct 2005
Location: Overland Park, Ks.
Posts: 5,229
|
Re: Lower control arm question
I havn't done any for a long time but it seems the locating dimples are to the rear.
|
|
|
|
|
08-26-2013, 05:05 PM
|
#6 |
|
Registered User
Join Date: Aug 2012
Location: Neskowin OR
Posts: 1,153
|
Re: Lower control arm question
I checked mine to make sure I put them together right, and they are both towards the front. All the pics I found show them in the front after that, and it looks like they fit right with them there. I'm not sure it would hurt it to put it in the back, besides maybe the arm sitting in a slightly different position.
|
|
|
|
|
08-26-2013, 05:22 PM
|
#7 |
|
Registered User
Join Date: Aug 2012
Location: Denver, Co
Posts: 245
|
Re: Lower control arm question
Yup, I just did mine a few weeks ago and went through this same process! The dimples go in the front. I don't think they will fit the other way around because there is a stud that fits in the dimples on the front u-bolt. If the dimples are in the rear the stud will not let the shaft sit flush in the bracket.
__________________
Will 1970 CST10 SWB LQ4/4L80E 2004 Silverado (sold) 2007.5 Dodge Ram 2500 |
|
|
|
|
08-26-2013, 05:24 PM
|
#8 | |
|
Registered User
Join Date: Aug 2012
Location: Neskowin OR
Posts: 1,153
|
Re: Lower control arm question
Quote:
|
|
|
|
|
|
08-26-2013, 08:23 PM
|
#9 |
|
Registered User
Join Date: Oct 2012
Location: Arlington Washington
Posts: 1,808
|
Re: Lower control arm question
It's been awhile thanks tlcrz
Posted via Mobile Device
__________________
Scott 67 c10 sold 89 c1500 90 k2500 91 s10 #chevyonly
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
<- My daughter loves this guy 8-)
Linear Mode
