Is a 650 carb enough for my combo? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dion · 12-19-2003, 01:46 AM

I posted this in the engine/drivetrain section also but this area gets more traffic and I need quick answers, thanks.

I'd figure yes but I thought I'd get your opinons, I'm looking at a Holley Q Jet replacement and what I've seen most of them are 650's, at least the one's I've seen.

**breeh** · 12-19-2003, 02:08 AM

A 650 should give you enough flow for a mildly modified 350. Alot of people tend to overcarbuerate their motors. More is not always better (unless of course you talking more cubic inches

)

**Stocker** · 12-19-2003, 10:51 AM

I would think so. Back in the late sixties I had a 65 Corvette with factory 327/365. It was 11:1 (or slightly higher, depends on what book you look at), 2.02 intake, ran like a scalded cat, and I'm pretty sure the Holley was 600 cfm. Pulled strong to 6500 redline.... dang, wish I still had that car!

WRMZ71 · 12-19-2003, 07:03 PM

650 should suit you just fine unless you got a really weak compression engine. But even then i think you would notive a difference over a quadrajet. I see people putting 750's on stock 350's and it drives me bonkers!!!

12-19-2003, 01:46 AM	#1
dion 72 Cheyenne Join Date: Oct 2001 Location: San Diego Posts: 2,086	Is a 650 carb enough for my combo? I posted this in the engine/drivetrain section also but this area gets more traffic and I need quick answers, thanks. I'd figure yes but I thought I'd get your opinons, I'm looking at a Holley Q Jet replacement and what I've seen most of them are 650's, at least the one's I've seen. __________________ Burnout Idle 1972Cheyenne 1966/67Stouts

12-19-2003, 02:08 AM	#2
breeh Recovering 67-72 Addict Join Date: Oct 2000 Location: North Bend, WA Posts: 1,788	A 650 should give you enough flow for a mildly modified 350. Alot of people tend to overcarbuerate their motors. More is not always better (unless of course you talking more cubic inches ) __________________ 68 Short Fleet 4x4; 427; BTO Level 3 700R4; NP205; Dana 60 front and rear; 4" lift with 35's; Disc brakes; AGR variable ratio steering; factory bucket seats; factory tach and tilt. "Friends call me cruzer cuz I like fast cars and fast women"

12-19-2003, 10:51 AM	#3
Stocker 20' Daredevil (Ret) Join Date: May 2003 Location: Jefferson State Posts: 13,693	I would think so. Back in the late sixties I had a 65 Corvette with factory 327/365. It was 11:1 (or slightly higher, depends on what book you look at), 2.02 intake, ran like a scalded cat, and I'm pretty sure the Holley was 600 cfm. Pulled strong to 6500 redline.... dang, wish I still had that car! __________________ - Mike - 1972 K20 LWB 350/350/205 RIP El Jay

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-19-2003, 07:03 PM	#4
WRMZ71 Cause the Chicks DIG IT!! Join Date: Nov 2003 Location: Beaufort SC Posts: 509	650 should suit you just fine unless you got a really weak compression engine. But even then i think you would notive a difference over a quadrajet. I see people putting 750's on stock 350's and it drives me bonkers!!!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.