|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-24-2003, 12:49 PM
|
#1 |
|
Registered User
Join Date: Jan 2003
Location: Mesa, AZ
Posts: 173
|
Has anybody had this problem?
I'm installing an ECE front end rebuild kit on my 72 Chevy 1/2 2WD and have run into a problem with installing the lower A-arm shafts. First off, I'm having a hard time even getting the shafts into the position in the A-arm. It's almost as though one-side of the A-arm is bent. I'm tempted to use a bottle jack to seperate the two tabs on the A-frame where the shaft goes. I'm wondering if anyone has run into anything like this before.
Even if I where to get the shafts into the A-arms, I wouldn't be able to get the nuts started straight into the A-arms beacuse of the bent tab on the A-frame. I can get the nut started on the shaft straight, but when it starts to thread into the A-frame it gets all crossed up. Any advice or experience that you guys have would be greatly aprreciated. |
|
|
|
12-24-2003, 01:28 PM
|
#2 |
|
Robert Olson Transport
 
Join Date: Oct 2002
Location: recent transplant to NC USA
Posts: 20,302
|
never used a ECE kit did ya try calling customer service? how much are these kits etc?
__________________
Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!! |
|
|
|
12-24-2003, 03:10 PM
|
#3 |
|
Registered User
Join Date: Oct 2002
Location: Des Moines WA. (Kent, area)
Posts: 668
|
ttt, i'd like to know also.
__________________
70 chev c10 swb fleet 72 grill, sb 400, 2/4 drop. 68 chev c10 swb fleet Early classic 4/6 drop with 4wheel disc brakes 9"rear 67-8 buckets tilt and A/C Classic GM Truck Club of Washington . |
|
|
|
|
12-24-2003, 04:07 PM
|
#4 |
|
Registered User
Join Date: Jan 2003
Location: Mesa, AZ
Posts: 173
|
The kit from ECE is $525, and is very complete. Comes with everything you need, and they're all Moog components. I really don't think that its a customer service issue, although I did have an issue with some U-bolts that I bought from them and they handled it great! I would never hesitate to by from those guys again.
I really think that I'm dealing with some "tweaked" A-arms and am going to have to end up getting replacements. It's really frustrating because I already them powdercoated and the ball joints are pressed in too! |
|
|
|
|
12-24-2003, 05:38 PM
|
#5 |
|
I am a Referee of life.
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,993
|
I would contact customer service or tech support.They may have a trick that they use to get everything to line up.It can't hurt and may save you $$$ in the long run.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
