![]() |
![]() |
#1 |
Registered User
![]() Join Date: Oct 2009
Location: SoCal
Posts: 815
|
Stepside Bed Question
Ive done bed wood in my 65 fleet, but Iam wanting to do it now on my 74 stepside. Question is..are the bottom side pieces spot welded to the sides? I removed all the wood except the 2 side pieces of wood because the "L" shaped side metal seems attached.
|
![]() |
![]() |
![]() |
#2 |
Registered User
![]() Join Date: Oct 2009
Location: SoCal
Posts: 815
|
Re: Stepside Bed Question
These are the pieces Iam asking about.
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Sep 2009
Location: Beaverton, OR from WA State
Posts: 1,515
|
Re: Stepside Bed Question
Looking at the page in the Illustration catalog, looks like it is part of the bedside. I have no experience with stepsides, other than admiring some nicely restored ones.
Looking closely it appears there is two spot welds, or two bolts bolting it to the side panel.
__________________
Devin 1983 GMC High Sierra 2500, 4x4, RC/LB, 400 S.B., SM-465, NP-208, Corporate 10 bolt & 9.5" 14 bolt 1996 GMC Sierra SLE 3500 DRW, 4x4, EC/LB, Vortec 454, NV-4500, BW-4401, AAM 925 & AAM 1050 1997 GMC Sierra SLT 1500 4x4, Z71/F44, EC/SB, Vortec 350 My Introduction with my '83s History New Daily, the '96 |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jan 2011
Location: Port Coquitlam, BC
Posts: 202
|
Re: Stepside Bed Question
I just finished doing my bed and the angle strips are spot welded to the bed sides. To remove the boards on either side, you need to unholy the bedsides from the crossmembers and lift them off. If you also need to replace the steel, I believe there is a good how-to on mar-k's website. It involves drilling out the spot welds and welding the new angle strips in.
Posted via Mobile Device
__________________
Proud UA member since 2009 My LT1 Silverado build-up: http://67-72chevytrucks.com/vboard/s...d.php?t=549660 Check out my new YouTube channel! - https://youtube.com/channel/UCXk5mZOQI1sEnu5bIkhe7fA |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jun 2004
Location: El Lago, TX
Posts: 1,668
|
Re: Stepside Bed Question
You can replace the wood without removing the spot welded angle strip. You have to destroy the original wood to get it out. Cut notches in the new wood where the bolts go through the angle strip and the wood will slip right in. You can't see the notches when it's installed. Here is a picture of mine that I recently did.
![]() |
![]() |
![]() |
![]() |
#6 |
Registered User
![]() Join Date: Oct 2009
Location: SoCal
Posts: 815
|
Re: Stepside Bed Question
Thanks for the replies. I guess either leave them in or drill out all the spot welds to replace them like this..I prefer the look with ALL the stainless .
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jan 2014
Location: Crestview, Florida
Posts: 37
|
Re: Stepside Bed Question
They are spot welded about every three inches, so that is a lot of drilling.
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|