WTB: Edelbrock\Holley 750 carb - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Larry68GMC · 12-22-2003, 11:55 AM

Anyone got one? Prefer manual choke...thanks

J.Lance · 12-22-2003, 12:12 PM

I have a Edelbrock performer 750 that needs gone through. If I remember right, it is an electric choke. It was on a motor I bought that had been sitting for quite a while and has some crust on the internals of the carb. I'd take $50 plus the ride if you are interested.

Also have a Holley single pump, 1978 L82 replacement carb. Not sure of the CFM but I think it is 600, electric choke. Ran good on a motor I had but had been sitting previously and was leaking fuel out of the tube that connects the front and rear bowls. I ended up throwing on a different carb and shelved it. Only had about 3000 miles on the carb when I got it. Also it is a spread bore. I take $50 for that one too.

Jason

Larry68GMC · 12-22-2003, 12:23 PM

Can you post some pics of the Edelbrock? Thanks

J.Lance · 12-22-2003, 12:26 PM

I can certainly do that but won't be until later this evening after I get back from work.

Larry68GMC · 12-22-2003, 12:28 PM

Ok sounds good..

J.Lance · 12-22-2003, 11:57 PM

My apologies, it is actually a Carter AFB. I ran the numbers in the Carter book a while back and it is a 750. I needed a 600 so I didn't use it. The part number is 9755S 0185.

breeh · 12-23-2003, 12:38 AM

I've got a 750 Holley Musclecar replacement. It is on my 427 now and works great. Unfortunately, it is not the best carb for a 4x4. It doesn't like being tipped over 40 degrees. I was running it on my Camaro before it went on the truck. It does have an electric choke though. If interested, I will take $100.00 plus the ride. It cost me over 400.00 new.

Larry68GMC · 12-23-2003, 02:04 AM

breeh, can you get some pics of that carb or the numbers?..thanks.....Larry

Larry68GMC · 12-23-2003, 02:10 AM

Lance...PM sent.

breeh · 12-24-2003, 05:37 PM

Here are the pics. The numbers that are on the choke horn are:
80509
1085

breeh · 12-24-2003, 05:38 PM

The Holley site says this is an 830 CFM but when I purchased it from Summit it was advertised as a 750 CFM. Go figure??

breeh · 12-26-2003, 05:21 PM

TTT

truckpower429 · 12-27-2003, 03:08 AM

Dang Larry if i knew that you were needing one ..i have and extra edelbrock 750 cfm ..pm me or email me and if interested ..let me know..we might be able to work something out ... Willie

danho · 12-27-2003, 02:14 PM

http://www.pirate4x4.com/forum/showt...hreadid=171206

HTH.
Dan.

*1972C10* · 01-04-2004, 11:42 PM

Ive got a milled down 750 holler No choke. 150$

12-22-2003, 11:55 AM	#1
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	WTB: Edelbrock\Holley 750 carb Anyone got one? Prefer manual choke...thanks __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

12-22-2003, 12:12 PM	#2
J.Lance Too many is never enough! Join Date: May 2003 Location: Idaho Falls, ID Posts: 455	Edelbrock I have a Edelbrock performer 750 that needs gone through. If I remember right, it is an electric choke. It was on a motor I bought that had been sitting for quite a while and has some crust on the internals of the carb. I'd take $50 plus the ride if you are interested. Also have a Holley single pump, 1978 L82 replacement carb. Not sure of the CFM but I think it is 600, electric choke. Ran good on a motor I had but had been sitting previously and was leaking fuel out of the tube that connects the front and rear bowls. I ended up throwing on a different carb and shelved it. Only had about 3000 miles on the carb when I got it. Also it is a spread bore. I take $50 for that one too. Jason __________________ Jason 1968 K10 SWB Fleetside 1971 K2500 GMC LWB 1968 K20 (later frame, donor body) 1972 C20 LWB parts truck 1993 K2500 Suburban, tow rig, 454, 4L80E NEW!! 18' Siem's car hauler 2004 Honda Odyssey (family man!)

12-22-2003, 12:23 PM	#3
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	Can you post some pics of the Edelbrock? Thanks __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

12-22-2003, 12:26 PM	#4
J.Lance Too many is never enough! Join Date: May 2003 Location: Idaho Falls, ID Posts: 455	carb I can certainly do that but won't be until later this evening after I get back from work. __________________ Jason 1968 K10 SWB Fleetside 1971 K2500 GMC LWB 1968 K20 (later frame, donor body) 1972 C20 LWB parts truck 1993 K2500 Suburban, tow rig, 454, 4L80E NEW!! 18' Siem's car hauler 2004 Honda Odyssey (family man!)

12-22-2003, 12:28 PM	#5
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	Ok sounds good.. __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

12-22-2003, 11:57 PM	#6
J.Lance Too many is never enough! Join Date: May 2003 Location: Idaho Falls, ID Posts: 455	carb My apologies, it is actually a Carter AFB. I ran the numbers in the Carter book a while back and it is a 750. I needed a 600 so I didn't use it. The part number is 9755S 0185. Attached Images __________________ Jason 1968 K10 SWB Fleetside 1971 K2500 GMC LWB 1968 K20 (later frame, donor body) 1972 C20 LWB parts truck 1993 K2500 Suburban, tow rig, 454, 4L80E NEW!! 18' Siem's car hauler 2004 Honda Odyssey (family man!)

12-23-2003, 12:38 AM	#7
breeh Recovering 67-72 Addict Join Date: Oct 2000 Location: North Bend, WA Posts: 1,788	I've got a 750 Holley Musclecar replacement. It is on my 427 now and works great. Unfortunately, it is not the best carb for a 4x4. It doesn't like being tipped over 40 degrees. I was running it on my Camaro before it went on the truck. It does have an electric choke though. If interested, I will take $100.00 plus the ride. It cost me over 400.00 new. __________________ 68 Short Fleet 4x4; 427; BTO Level 3 700R4; NP205; Dana 60 front and rear; 4" lift with 35's; Disc brakes; AGR variable ratio steering; factory bucket seats; factory tach and tilt. "Friends call me cruzer cuz I like fast cars and fast women"

12-23-2003, 02:04 AM	#8
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	breeh, can you get some pics of that carb or the numbers?..thanks.....Larry __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

12-23-2003, 02:10 AM	#9
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	Lance...PM sent. __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

12-24-2003, 05:37 PM	#10
breeh Recovering 67-72 Addict Join Date: Oct 2000 Location: North Bend, WA Posts: 1,788	Here are the pics. The numbers that are on the choke horn are: 80509 1085 Attached Images __________________ 68 Short Fleet 4x4; 427; BTO Level 3 700R4; NP205; Dana 60 front and rear; 4" lift with 35's; Disc brakes; AGR variable ratio steering; factory bucket seats; factory tach and tilt. "Friends call me cruzer cuz I like fast cars and fast women"

12-24-2003, 05:38 PM	#11
breeh Recovering 67-72 Addict Join Date: Oct 2000 Location: North Bend, WA Posts: 1,788	The Holley site says this is an 830 CFM but when I purchased it from Summit it was advertised as a 750 CFM. Go figure?? Attached Images __________________ 68 Short Fleet 4x4; 427; BTO Level 3 700R4; NP205; Dana 60 front and rear; 4" lift with 35's; Disc brakes; AGR variable ratio steering; factory bucket seats; factory tach and tilt. "Friends call me cruzer cuz I like fast cars and fast women" Last edited by breeh; 12-24-2003 at 05:44 PM.

12-26-2003, 05:21 PM	#12
breeh Recovering 67-72 Addict Join Date: Oct 2000 Location: North Bend, WA Posts: 1,788	TTT __________________ 68 Short Fleet 4x4; 427; BTO Level 3 700R4; NP205; Dana 60 front and rear; 4" lift with 35's; Disc brakes; AGR variable ratio steering; factory bucket seats; factory tach and tilt. "Friends call me cruzer cuz I like fast cars and fast women"

12-27-2003, 03:08 AM	#13
truckpower429 Registered User Join Date: Nov 2003 Location: Okc, Oklahoma Posts: 33	Dang Larry if i knew that you were needing one ..i have and extra edelbrock 750 cfm ..pm me or email me and if interested ..let me know..we might be able to work something out ... Willie

12-27-2003, 02:14 PM	#14
danho Pesemistic Optimist Join Date: Dec 2002 Location: Prineville, Oregon Posts: 227	http://www.pirate4x4.com/forum/showt...hreadid=171206 HTH. Dan.

01-04-2004, 11:42 PM	#15
1972C10 Account Suspended Join Date: Dec 2003 Location: Texas Posts: 2,686	Ive got a milled down 750 holler No choke. 150$



Register or Log In To remove these advertisements.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.