Walter DeWayne...Walt for short

[nlped]

Hey All,

Thought I'd introduce my new aquisition and preface this build thread with the fact that I really won't get much done to it until the weather breaks here in the MUGGY south, but I wanted to start the thread on day 1.

Truck... 1968 2wd Custom SWB Fleet. 283 (?), 3 OTT, open diff rear. Options are few...push button radio, chrome front & rear bumpers, and side trim is about all I can make out on the SPID. Original paint, motor, trans, hubcaps, wheels etc. You get the jist.

Plan... 5.3/4L60e with CTSV oil pan, PSI harness and reflashed ECU, Jeep Wrangler rear tank with A/C Delco EFI pump and s/s fuel lines rear to front, Painless harness, Inlinetube stainless hardlines and s/s braided hard to caliper & rear lines, PB Mild front Dropmember, PB rear Mild/Touring rear dropmember with PB tubular rear trailing arms, PB crossmembers, bags, Staggered 18" Boss 338's, Wilwood 14" 6-piston fronts & Wilwood 13" rear brakes, built '70-72 12 bolt (Eaton diff, 3.73's), Wilwood M/C and p/v... I ALREADY HAVE THESE PIECES SO I WILL BE USING THEM . I have lot's of other parts, but dang if I can remember them...

Wish list includes A/C, power windows & locks, scuff & clear the paint and drive the heck out of ole Walt.

[nlped]

More pics...

[Joe Pass]

Pretty cool project..Thanks for the pictures

[Xeen]

I can dig it, It looks like a great ole truck.
Subbed.

[nlped]

I forgot the back story...

Bought it from the Grandson of the original owner (named Walter DeWayne "last name")...hence the inevitable name of the project. Last time Walter drove Walt was in 1984, the truck has literally been sitting in a "barn" since then. Move forward to 2014 and Grand Father died and grandson inherited the property and wasn't keen on ole Walt, so I scored him. I have the original bill of sale, books, pamphlets etc.

Did I mention that I'm STOKED!!!

[screaminchevypickup]

Great looking truck! sounds like you have some good plans for it..

[litew8]

Not a lot of rust it looks like. SPID seen better days.

[Oldtruckfanatic]

Id kill to find a truck with that patina. Lucky !

[nlped]

Originally Posted by screaminchevypickup

Great looking truck! sounds like you have some good plans for it..

PM'ed you

[mx289]

Very cool truck Ed.
And you have some sweet plans for it.

[nlped]

Originally Posted by Joe Pass

Pretty cool project..Thanks for the pictures

Pics are going to be plenty on this one. Thanks for the compliments

Originally Posted by Xeen

I can dig it, It looks like a great ole truck.
Subbed.

Man, I'm so excited about this one... Thanks!!

Originally Posted by litew8

Not a lot of rust it looks like. SPID seen better days.

SPID is certainly beat, but not much to see... Almost no options. And rust wise, it's really clean for this part of the country.

Originally Posted by Oldtruckfanatic

Id kill to find a truck with that patina. Lucky !

Yep, when I saw it, I knew I had to have it.

Originally Posted by mx289

Very cool truck Ed.
And you have some sweet plans for it.

Thanks Man! I'm stoked about this one.

[Bennett68C10]

Nice looking truck, can't wait to see the transformation

[thelonerife]

OMG. OMG. Good Buy!

[nlped]

Originally Posted by Bennett68C10

Nice looking truck, can't wait to see the transformation

Thanks Keith.... I'll hopefully get a real start on it really soon.

Originally Posted by thelonerife

OMG. OMG. Good Buy!

I think so too. Thanks Chuck! Guess I'll know more when I start the transformation.

[nlped]

I've tentatively made an order for PB stuff from one of our board vendors. Mild front dropmember, tubular upper & lower control arms, trans crossmember, trailing arms & crossmember, R&P, front shock relocation brackets & 3 joint steering shaft.

[nlped]

PB trailing crossmember bought here on the site today. I need a mild md and trailing arms and I'm ready. Whoop whoop

[nlped]

Well, I got all the front PB dropmember stuff bought today from a member on here. Now all I need is a set of PB trailing arms & I'm set. Anybody ?

[Bennett68C10]

Nice parts pickup, you doing mild dropmembers front and rear?

[nlped]

No, in the rear I'm only going with the 2 piece notch, so very mild drop in the rear. If, by some chance, I could find the mild rear notch & bridge, I'd go that route though.

[knomadd]

Nice score! I'll be following along. I like your plans, should be great when it's done.

[c10Dream'n]

this should be good, especially with the list of parts you mentioned.

[nlped]

And I got the PB trailing arms ordered this morning from member "LaidBackRecreations". I think that's all I need...at least for awhile

[nlped]

Well, it's been awhile since I've done anything related to ole Walt because of the newest acquisition, Chubby. But I did get over to the Fastenal store and pick up my PB front dropmember pieces & parts. Looks like everything is there, but the balljoints and CPP modular spindles aren't the '73 up pieces I was told , so I guess I'll have to sell the spindles and buy new balljoints. I'm going to use my McGaughy big brake spindles as I don't need the extra narrow"ness" of the CPP spindles with the 1" narrower PB control arms. I was going to use them on another project, but oh well.

Just a funny picture of my pickup vehicle... My wife drove my truck to work today, so I made do

[nlped]

All I'm waiting on is my trailing arms and I'll be PB equipped. Then I'll start tearing into Walt.

[soundqdoug]

PLEASE don't paint it!