|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-17-2014, 04:50 PM
|
#1 |
|
Registered User
Join Date: Apr 2013
Location: California
Posts: 2
|
Keyway Pulley Puller Tool
Hi all!
Thank you in advance. I'm stuck. My power steering pump went bad. I am looking to buy the right tool for a keyway power steering pump pulley for my 1971 Chevy C20 350. I previously used a generic pulley puller but I could not get my pulley back on with the generic tool. The manual calls for special tools. I do not have the manual in front of me, but I can post a pic of the tool specs later when I get home. I've attached a pic of the pulley. |
|
|
|
12-17-2014, 07:12 PM
|
#2 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: Keyway Pulley Puller Tool
any local autoparts store should have the proper tool it is about $12
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
12-17-2014, 07:36 PM
|
#3 |
|
Moderator
 
Join Date: May 2007
Location: Southern Cal
Posts: 20,031
|
Re: Keyway Pulley Puller Tool
Harbor freight carries it too. You need this instead of a three jaw puller
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul |
|
|
|
|
12-17-2014, 07:38 PM
|
#4 |
|
Moderator
Join Date: May 2007
Location: Southern Cal
Posts: 20,031
|
Re: Keyway Pulley Puller Tool
Stuff inside
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul |
|
|
|
|
12-17-2014, 07:58 PM
|
#5 |
|
Registered User
Join Date: Oct 2014
Location: JBLM
Posts: 20
|
Re: Keyway Pulley Puller Tool
Not to bogart your question but i think i am having power stearing problems. When ever im stationary and try to turn the wheele its turns very rough. Any thoughts.
|
|
|
|
|
12-17-2014, 08:02 PM
|
#6 |
|
Senior Member
 
Join Date: Jun 2005
Location: Winona Lake, IN
Posts: 6,414
|
Re: Keyway Pulley Puller Tool
The style that uses the nut is not a press fit but if it's been on there a while you may need a puller to remove it. After you get it off put some never seize on the shaft and you should be able to remove it by hand after that.
__________________
70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear |
|
|
|
|
| Bookmarks |
| Tags |
| #keyway, #powersteering pulley, #pulley, #pulley puller |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
