AZ Two SWB Driveshafts

[mahanian]

I have two SWB driveshafts, one 2-piece that was behind a TH-400 and one 1-piece that was behind a 4-speed. I'd like $118 each shipped or $80 each picked up.

[wgeyer88]

I'm looking for a th400 slip yoke to use on my 4l80e if you're willing to split it up.

Thanks
-Will

[mahanian]

Thanks but I'd rather sell them as a complete driveshaft unless a buyer wants the driveshaft without the TH400 yoke.

[wgeyer88]

No problem, I completely understand.

Thanks

[mmiddle]

where in AZ are you? My kid goes to Embry-Riddle in Prescott. I might be interested in the TH400 shaft.

[mahanian]

I'm in the Phoenix area

[ScottH]

jared can u tell me the length of the 1 piece when u get a chance?
No hurry on my end.

Thanks
Scott

[mahanian]

Hey Scott, the 1 piece is 56"-56 1/4" between U-joint centerlines, a little hard to measure by myself

[ScottH]

Thanks for checking, it may be a bit b4 I know exactly what length I need.
Will check back with u then to see if it is still available.

Scott

[tsmith]

Does the 2 piece come with the carrier bearing?

[mahanian]

yep, it's still on it

[tsmith]

Do you have any pics of the two piece and do you do paypal

[OLEBEATER]

I am interested in the 1 piece shaft. I will checek the length I need toninght and let you know. I am in virginia, will the $118 be the same? Thanks.........Ro

[mahanian]

Originally Posted by tsmith

Do you have any pics of the two piece and do you do paypal

I will get some pics tonight, paypal works if you are willing to cover the fees.

Originally Posted by OLEBEATER

I am interested in the 1 piece shaft. I will checek the length I need toninght and let you know. I am in virginia, will the $118 be the same? Thanks.........Ro

Ok, let me know, yes that price will cover shipping

[mahanian]

Sorry for the delay, here are the pictures. They are both in good shape and could be used as is but I would recommend replacing the U-joints just as a maintenance thing, I'm sure they are either original or really old. I greased and bagged the slip yokes to prevent rusting (I bought the 1 piece used so it had surface rust already) so you will need to clean them and steel wool them.

[mahanian]

1-piece sold pending payment

[mahanian]

The one piece is sold but I still have the 2 piece driveshaft for sale with the beefy TH400 yoke

[mahanian]

ttt

[70STOVEBOLT]

Do you know if the 2-PC shaft is the correct length for a big block?

Thanks,
Mark

[mahanian]

I'm not sure if the motor size shifts the transmission position, I thought the motor mounts accounted for that. I've only seen driveshaft lengths categorized by transmission and bed length. There is only one set of transmission cross member mounting holes on my frame so I think the transmission is always in the same spot

[kaphillips]

I am not that far in Amarillo TX, would you take an offer of 90 shipped to me in Amarillo on the 2 piece ds with th400 yoke. Please and pretty please.

[mahanian]

Sorry bud, it's going to cost me at least $35 to ship it due to its length so I can't go that low

[bntmotorcycles]

I will take the 2piece shaft. It is for 115" chassis? $118 shipped correct? Art. 317-835-4544

[mahanian]

Originally Posted by bntmotorcycles

I will take the 2piece shaft. It is for 115" chassis? $118 shipped correct? Art. 317-835-4544

Yes, it's from my short bed, $118 shipped. I'll send you a PM.