AD inner cowl panel - The 1947 - Present Chevrolet & GMC Truck Message Board Network

54 LS-3100 · 06-02-2015, 12:09 AM

Gentlemen, I have some patch panels on order and I had a couple questions on where to start.

I am replacing part of the floor, inner to out cowl panel, and inner cowl panel (kick panel). The outer cowl doesn't need replaced because they are straight and only the very bottom portion needs fixed.

I was thinking about starting at the inner cowl panel and working my way out to the inner to outer panel. Decent plan? Also, what is the best way to remove the inner to outer w/o removing the outer panel? Drill the spot welds and pop it out?

Thank guys

Chevy-49 · 06-02-2015, 01:48 AM

I will do same the same, from the inside out, drilled out welds, inner cowl panel is very rusted, it came out easily.

**mr48chev** · 06-02-2015, 10:51 AM

I've got the same thing to do and have been pondering how to do it without taking the whole section of the cowl apart and still make it look right.

67GMCkid · 06-02-2015, 03:34 PM

I pondered this same question on the passenger side of mine. I hated the thought of destroying original rust free body metal but, that was until I got into it and realized that even though it had not rusted thru it had become paper thin over the years. I was also glad that I had ordered the complete panel as it was almost as thin at the top as it was near the bottom... The amount of time saved and the better clean up and proper prep of the hidden areas was well worth the extra few dollars spent on the complete panel..

**mr48chev** · 06-02-2015, 05:48 PM

I figured I was (and may still have to) going to have to drill the spot welds out on the outside panels and work my way in to replace the inside kick panels on mine.

It isn't that big of an expense but If I have to take it all apart it is going to take some time to do it right.

greg_h · 06-02-2015, 10:32 PM

The inner cowl panels do not fit. I had to straighten and re-bend the curve to fit. I didn't use the inner to outer panels as they too struck me as home made looking. The notches to go around the inner cowl ribs are too wide. I chose to use the center section of the inner to outers and tray and save the more original looking panels.

54 LS-3100 · 06-03-2015, 12:37 AM

Quote:

Originally Posted by greg_h

The inner cowl panels do not fit. I had to straighten and re-bend the curve to fit. I didn't use the inner to outer panels as they too struck me as home made looking. The notches to go around the inner cowl ribs are too wide. I chose to use the center section of the inner to outers and tray and save the more original looking panels.

Who did you go through when you bought the panels? Remember the brand by chance?

greg_h · 06-03-2015, 10:33 PM

Classic...Back when I bought them, I think they were still known as ChevyDuty.

06-02-2015, 12:09 AM	#1
54 LS-3100 Registered User Join Date: Feb 2015 Location: Clinton, MO Posts: 29	AD inner cowl panel Gentlemen, I have some patch panels on order and I had a couple questions on where to start. I am replacing part of the floor, inner to out cowl panel, and inner cowl panel (kick panel). The outer cowl doesn't need replaced because they are straight and only the very bottom portion needs fixed. I was thinking about starting at the inner cowl panel and working my way out to the inner to outer panel. Decent plan? Also, what is the best way to remove the inner to outer w/o removing the outer panel? Drill the spot welds and pop it out? Thank guys Attached Images

06-02-2015, 01:48 AM	#2
Chevy-49 Registered User Join Date: May 2013 Location: Losser, The Netherlands Posts: 136	Re: AD inner cowl panel I will do same the same, from the inside out, drilled out welds, inner cowl panel is very rusted, it came out easily. __________________ . My build thread: 1949 AD truck 'Chevy-49'

06-02-2015, 10:51 AM	#3
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,705	Re: AD inner cowl panel I've got the same thing to do and have been pondering how to do it without taking the whole section of the cowl apart and still make it look right. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

06-02-2015, 03:34 PM	#4
67GMCkid Registered User Join Date: Jun 2012 Location: Etters Pa Posts: 197	Re: AD inner cowl panel I pondered this same question on the passenger side of mine. I hated the thought of destroying original rust free body metal but, that was until I got into it and realized that even though it had not rusted thru it had become paper thin over the years. I was also glad that I had ordered the complete panel as it was almost as thin at the top as it was near the bottom... The amount of time saved and the better clean up and proper prep of the hidden areas was well worth the extra few dollars spent on the complete panel..

06-02-2015, 05:48 PM	#5
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,705	Re: AD inner cowl panel I figured I was (and may still have to) going to have to drill the spot welds out on the outside panels and work my way in to replace the inside kick panels on mine. It isn't that big of an expense but If I have to take it all apart it is going to take some time to do it right. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

06-02-2015, 10:32 PM	#6
greg_h Registered User Join Date: Apr 2015 Location: Enid OK Posts: 85	Re: AD inner cowl panel The inner cowl panels do not fit. I had to straighten and re-bend the curve to fit. I didn't use the inner to outer panels as they too struck me as home made looking. The notches to go around the inner cowl ribs are too wide. I chose to use the center section of the inner to outers and tray and save the more original looking panels.

06-03-2015, 10:33 PM	#8
greg_h Registered User Join Date: Apr 2015 Location: Enid OK Posts: 85	Re: AD inner cowl panel Classic...Back when I bought them, I think they were still known as ChevyDuty.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.