Relacing factory rivets. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

lrmarquez80 · 11-09-2015, 08:02 PM

I was wanting some advice replacing factory rivets. I'm working on 71 Chevy fleetside frame. Im wanting to replace the rivets on the cross members. What would be the best bolt, or would it even be a good idea to replace the rivets??! Thanks.
Posted via Mobile Device

rocknss · 11-09-2015, 09:20 PM

If they are fine I would leave them alone, but if not use grade 8 hardware. I replaced some of the rivets on my Burbs frame that were bad and that's what I used.

**LockDoc** · 11-09-2015, 09:34 PM

-
I agree with rocknss. Grade 8 bolts and make sure they fit the holes snug. If you have to, drill the holes out to the next bolt size to get the closest fit possible.

LockDoc

swamp rat · 11-09-2015, 10:32 PM

My advice, if you drill do it one rivit at a time to maintain the geometry of the frame.

lrmarquez80 · 11-09-2015, 11:24 PM

I appreciate the feedback
Posted via Mobile Device

11-09-2015, 08:02 PM	#1
lrmarquez80 Registered User Join Date: Jul 2015 Location: Amarillo, tx Posts: 8	Relacing factory rivets. I was wanting some advice replacing factory rivets. I'm working on 71 Chevy fleetside frame. Im wanting to replace the rivets on the cross members. What would be the best bolt, or would it even be a good idea to replace the rivets??! Thanks. Posted via Mobile Device

11-09-2015, 09:20 PM	#2
rocknss Registered User Join Date: Oct 2004 Location: Milwaukee, WI Posts: 403	Re: Relacing factory rivets. If they are fine I would leave them alone, but if not use grade 8 hardware. I replaced some of the rivets on my Burbs frame that were bad and that's what I used. __________________ Steven 69 Chevy C10 Suburban 350 700R4 w/Disc brakes on all four corners 2017 50th Anniversary Camaro SS 2004 Chevy Impala LS 2016 Chevy Malibu LT

11-09-2015, 09:34 PM	#3
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,771	Re: Relacing factory rivets. - I agree with rocknss. Grade 8 bolts and make sure they fit the holes snug. If you have to, drill the holes out to the next bolt size to get the closest fit possible. LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

11-09-2015, 10:32 PM	#4
swamp rat Registered User Join Date: Oct 2007 Location: Spanaway Posts: 8,451	Re: Relacing factory rivets. My advice, if you drill do it one rivit at a time to maintain the geometry of the frame. __________________ Mike. Swamp Rat build thread : http://67-72chevytrucks.com/vboard/s...d.php?t=595019 72 3/4T 4X4 4" BDS Lift 33" BFG's

11-09-2015, 11:24 PM	#5
lrmarquez80 Registered User Join Date: Jul 2015 Location: Amarillo, tx Posts: 8	Re: Relacing factory rivets. I appreciate the feedback Posted via Mobile Device

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.