![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
![]() Join Date: Oct 2015
Location: Allen, TX
Posts: 63
|
87 Tank in a 75. Filler hose options?
I'm getting close to finishing my EFI conversion and have swapped out my '75 tanks for '87 TBI tanks in order to use in-tank pumps. All was good until I noticed that the '87 tanks accept 1 3/4" filler hoses where my '75 was 1 3/8". Obviously, my new 1 3/8" hoses are not going to stretch over a 1 3/4" barb, so what are my options?
I've found a 1 3/4" 90 degree elbow (Gates 24716), with which I could use a short piece of 1 3/8" tubing as a reducer if the OD is close enough. Is that really my only option? I doubt I'm going to find a molded hose that fits perfectly, but hopefully someone here has ran into this before and has a solution! |
![]() |
![]() |
![]() |
#2 |
Registered User
![]() Join Date: Jul 2014
Location: Sherwood, Oregon
Posts: 974
|
Re: 87 Tank in a 75. Filler hose options?
Can you go to an exhaust shop and get them to flare one end of the a section of tubing to fit over 1 3/8 and then flare the other end to 1 3/4 for the hose? They can also bend any angle you might need as well.
__________________
--Project BABA YAGA!... http://67-72chevytrucks.com/vboard/s...d.php?t=655783 --Project BABA YAGA!... http://67-72chevytrucks.com/vboard/s...ghlight=Belair "Life is tough - wear a cup!" "Old Enough to Know Better - Too Young to Resist" "Junk is something you will need three weeks after you throw it away." |
![]() |
![]() |
![]() |
#3 |
Registered User
![]() Join Date: Oct 2015
Location: Allen, TX
Posts: 63
|
Re: 87 Tank in a 75. Filler hose options?
The thought has crossed my mind, I'm just not sure how much you can expand that tubing. Expanding it 3/8" sounds like a lot to me.
|
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: Jul 2014
Location: Sherwood, Oregon
Posts: 974
|
Re: 87 Tank in a 75. Filler hose options?
Remember, 3/8" is the diameter, so you are only expanding it .1875" (3/16") radius... not .375". The exhaust shop can tell you the limits if it sounds too radical to you.
__________________
--Project BABA YAGA!... http://67-72chevytrucks.com/vboard/s...d.php?t=655783 --Project BABA YAGA!... http://67-72chevytrucks.com/vboard/s...ghlight=Belair "Life is tough - wear a cup!" "Old Enough to Know Better - Too Young to Resist" "Junk is something you will need three weeks after you throw it away." |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Mar 2015
Location: Manchester, CT
Posts: 433
|
Re: 87 Tank in a 75. Filler hose options?
You don't have to do any fancy footwork here. Just get the Gates hose . The early filler pipe is 1 3/4" just like the later tank, so the Gates hose will just slide on each piece
![]() I had to do this for my LS/'87 tank conversion. Just cut the new hose to match the dimension of the old hose. Even the vent hose from the early filler will fit onto the newer tank |
![]() |
![]() |
![]() |
#6 |
Registered User
![]() Join Date: Oct 2015
Location: Allen, TX
Posts: 63
|
Re: 87 Tank in a 75. Filler hose options?
That got me excited until I took a closer look at the filler neck in your picture. What you have there appears to be a 79-80 filler neck for use with a door, which is different from what I have.
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Mar 2015
Location: Manchester, CT
Posts: 433
|
Re: 87 Tank in a 75. Filler hose options?
Yeah, I do have an '80 Fleetside. Is your filler that much smaller?. How about if you just cut a piece of the original hose to fit on your filler, then slide the Gates hose over that, using the original hose as a spacer?
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|