Installed 4" lift today - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**JIMs70GMC** · 03-28-2004, 10:17 PM

Here's starting on the rear first:

**JIMs70GMC** · 03-28-2004, 10:18 PM

2

**JIMs70GMC** · 03-28-2004, 10:19 PM

3

**JIMs70GMC** · 03-28-2004, 10:20 PM

4 Frame bushing:

**JIMs70GMC** · 03-28-2004, 10:21 PM

5

**JIMs70GMC** · 03-28-2004, 10:22 PM

6

**JIMs70GMC** · 03-28-2004, 10:24 PM

7

**JIMs70GMC** · 03-28-2004, 10:30 PM

8

It took me about 5 hours to get what you see done. Still need to replace the shocks, steering arm and brake lines. I also need to buy a 7/8th deep socket so I can finish tightening the rear u-bolts. Hopefully Tuesday I'll be able to swap the steering arm, have to buy my brake lines tomorrow and have other brake issues to work out(need to replace a couple hard lines).
I found it was easier to just cut all the u-bolts off, since the kit came with all 8 u-bolts. Also cut the front spring bolts out. The shackle end spring bolts actually came off real easy.

Budweis · 03-28-2004, 11:28 PM

looking good , 5 hours seems like good time, cant wait to start mine, got a question for ya, when you take the springs off as long as got front off ground are they under any pressure? i took some off an old road runner one time and they popped and almost took head off lol. i think ill take my bed off too and sand everything down and undercoat, looks like a breeze to work on while its off, can two people lift off a bed or they pretty heavy?

Destructo · 03-29-2004, 12:09 AM

I don't remember how long it took me, but it was a good while for everything, I didn't torch anything off though, or cut. I soaked everything with PB Blaster the day before and the impact wrench took care of the rest. Its nice having every air tool you need and having all the tools a man could want except for some of the special stuff

looks just like my kit except I bought some rear springs off ebay for mine.

**JIMs70GMC** · 03-29-2004, 07:17 AM

Budweis, Take the u-bolts off the axle first then you can lower the axle and the spring will not be under a load. Don't forget to remove the shocks, they will limit travel down.
Destructo, This was my 4th lift install and after throwing away u-bolts after removing them, I made short work of it by cutting them off. My wimpy impact wrench wouldn't take them off.

Budweis · 03-29-2004, 07:38 AM

ok thanks for the tip, nothing like getting killed to ruin your weekend lol, i dont have a torch but maybe i could cut those off with pnuematic cut off tool. im going to start taking my bed off this week and get the new differential on the 17th once i get started on ill post some pics on how coming along. i definitely gonna have to go 4" suspension and 2" body as i just figured out truck already has 2 1/2" lift so a 4" wouldnt do much. i had truck somewhere else so didnt realize till went and got. i was wondering how it had 33's on it with no lift lol. or you think im better off going 6" suspension and no body lift?

**JIMs70GMC** · 03-29-2004, 07:55 AM

I used an angle grinder. Well I took a body lift off of the 71 and because of it I've had to correct so many things. Richard Morgan just installed 6" lift on his 72 and I took it for a drive. It looked good to me at the driveshaft angles, definetly need longer brake lines though.

Dean · 03-29-2004, 10:10 AM

Looking great! You will be cruisin soon. Don't you just love those rusty midwest suspension bolts? lol That new exhaust looks good. I bet that made it sound a whole lot better.

Did you find someone to pick up all your scrap metal?

784X4GUY · 03-29-2004, 01:16 PM

Looks real nice man...good luck with the rest of it.

**JIMs70GMC** · 03-29-2004, 03:01 PM

Thanks,

Dean, I ended up hauling it off my self. Have had three people tell me they want the flat bed but I still have it!

**Yukon Jack** · 03-29-2004, 04:00 PM

That's some great progress! Looking good.

griesel72 · 03-29-2004, 06:12 PM

looks good so far, you make quick work of a swap

**JIMs70GMC** · 03-29-2004, 10:33 PM

Griesel72, I have a very understanding wife.

72bigblock4wd · 03-30-2004, 10:51 PM

Looks like a pretty solid truck! I'm hoping to be doing the same thing soon. I have a '72 K10 I was going to do, but the cab's pretty rusty. I just found a nice '68 GMC K15 from the southwest that's virtually rustfree. I'm hoping to pick it up next week. Always nice to see another GMC!!!

03-28-2004, 10:17 PM	#1
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Installed 4" lift today Here's starting on the rear first: Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-28-2004, 10:18 PM	#2
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	another rear shot 2 Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-28-2004, 10:19 PM	#3
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	All done with rear: 3 Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-28-2004, 10:20 PM	#4
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Now up front 4 Frame bushing: Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-28-2004, 10:21 PM	#5
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	right front spring 5 Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-28-2004, 10:22 PM	#6
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	left front 6 Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-28-2004, 10:24 PM	#7
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	spring comparision 7 Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-28-2004, 10:30 PM	#8
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	front done(springs anyway) 8 It took me about 5 hours to get what you see done. Still need to replace the shocks, steering arm and brake lines. I also need to buy a 7/8th deep socket so I can finish tightening the rear u-bolts. Hopefully Tuesday I'll be able to swap the steering arm, have to buy my brake lines tomorrow and have other brake issues to work out(need to replace a couple hard lines). I found it was easier to just cut all the u-bolts off, since the kit came with all 8 u-bolts. Also cut the front spring bolts out. The shackle end spring bolts actually came off real easy. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-28-2004, 11:28 PM	#9
Budweis Geared for Collision Join Date: Jan 2004 Location: St. Louis, Mo. Posts: 683	looking good , 5 hours seems like good time, cant wait to start mine, got a question for ya, when you take the springs off as long as got front off ground are they under any pressure? i took some off an old road runner one time and they popped and almost took head off lol. i think ill take my bed off too and sand everything down and undercoat, looks like a breeze to work on while its off, can two people lift off a bed or they pretty heavy? __________________ MEMBER OF THE 4 WHEEL DISK BRAKE CLUB 1970 C/K20 3/4 Ton 1996 Collectors Edition Corvette 1977 Corvette Coupe

03-29-2004, 12:09 AM	#10
Destructo Registered User Join Date: Sep 2003 Location: Lewisville, NC Posts: 1,836	I don't remember how long it took me, but it was a good while for everything, I didn't torch anything off though, or cut. I soaked everything with PB Blaster the day before and the impact wrench took care of the rest. Its nice having every air tool you need and having all the tools a man could want except for some of the special stuff looks just like my kit except I bought some rear springs off ebay for mine. __________________ 1985 Scottsdale Shortbed 4x4 Stout 350 with some "upgrades"-700r4-33x12.5" Mud Tires, Warn 8274-50 winch. 2005 Chevrolet Colorado Regular Cab 2wd 4-banger, 5 speed, Street Pack with 3.73 axle.

03-29-2004, 07:17 AM	#11
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Budweis, Take the u-bolts off the axle first then you can lower the axle and the spring will not be under a load. Don't forget to remove the shocks, they will limit travel down. Destructo, This was my 4th lift install and after throwing away u-bolts after removing them, I made short work of it by cutting them off. My wimpy impact wrench wouldn't take them off. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-29-2004, 07:38 AM	#12
Budweis Geared for Collision Join Date: Jan 2004 Location: St. Louis, Mo. Posts: 683	ok thanks for the tip, nothing like getting killed to ruin your weekend lol, i dont have a torch but maybe i could cut those off with pnuematic cut off tool. im going to start taking my bed off this week and get the new differential on the 17th once i get started on ill post some pics on how coming along. i definitely gonna have to go 4" suspension and 2" body as i just figured out truck already has 2 1/2" lift so a 4" wouldnt do much. i had truck somewhere else so didnt realize till went and got. i was wondering how it had 33's on it with no lift lol. or you think im better off going 6" suspension and no body lift? __________________ MEMBER OF THE 4 WHEEL DISK BRAKE CLUB 1970 C/K20 3/4 Ton 1996 Collectors Edition Corvette 1977 Corvette Coupe

03-29-2004, 07:55 AM	#13
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	I used an angle grinder. Well I took a body lift off of the 71 and because of it I've had to correct so many things. Richard Morgan just installed 6" lift on his 72 and I took it for a drive. It looked good to me at the driveshaft angles, definetly need longer brake lines though. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-29-2004, 10:10 AM	#14
Dean Senior Member Join Date: Jan 2000 Location: Cincinnati, Ohio Posts: 1,492	Looking great! You will be cruisin soon. Don't you just love those rusty midwest suspension bolts? lol That new exhaust looks good. I bet that made it sound a whole lot better. Did you find someone to pick up all your scrap metal?

03-29-2004, 01:16 PM	#15
784X4GUY Did someone say MUD? Join Date: Aug 2003 Location: Pullman,WA Posts: 1,089	Looks real nice man...good luck with the rest of it. __________________ Im in the market guys...so keep ya eyes peeled -------------------- Mini trucks are for guys who cant get it up!



Register or Log In To remove these advertisements.

03-29-2004, 03:01 PM	#16
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Thanks, Dean, I ended up hauling it off my self. Have had three people tell me they want the flat bed but I still have it! __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-29-2004, 04:00 PM	#17
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	That's some great progress! Looking good. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

03-29-2004, 06:12 PM	#18
griesel72 Senior Member Join Date: Apr 2003 Location: Howard, Kansas USA Posts: 1,997	looks good so far, you make quick work of a swap __________________ 1969 K10 Custom 10 1997 Z71 2006 Volkswagen Jetta TDI 2006 King Ranch 1980 Wife

03-29-2004, 10:33 PM	#19
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Griesel72, I have a very understanding wife. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-30-2004, 10:51 PM	#20
72bigblock4wd Registered User Join Date: Feb 2004 Location: Grand Rapids, Michigan Posts: 194	JIMs70GMC Looks like a pretty solid truck! I'm hoping to be doing the same thing soon. I have a '72 K10 I was going to do, but the cab's pretty rusty. I just found a nice '68 GMC K15 from the southwest that's virtually rustfree. I'm hoping to pick it up next week. Always nice to see another GMC!!!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.