Guage bezel w/ Tach - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67chevy2wd · 03-29-2004, 08:51 PM

I have a Gauge Bezel with all the guages except the Vacum guage. I was just wondering if it is worth anything, also it is original and everything works.

SWEET7T · 03-29-2004, 08:57 PM

I will swap you a fresh $20 for it!!!

Actually, depending on how nice it is, could be worth $100+

FRENCHBLUE72 · 03-29-2004, 10:10 PM

Does it have a tach???

bouncytruck · 03-29-2004, 10:14 PM

Is it a 6 or 8 cyl tach? It should be stamped on the back of the tach. Value also depends on the condition (obviously). Is there any rust on the gauges, faded paint, scratches in the lens, etc.

Lobo'74 · 03-29-2004, 10:16 PM

I found a '67-'68 gages panel on e-bay and got it for about $56. Didn't have chrome, the gages all look fine. It fell off the box for my truck parts in the garage to the cement floor this winter. Only about a foot, but it hit on the upper right hand corner and broke the plastic bezel there. I've decided I like the non gauge dash the PO cut 2" holes in to mount gages. I've put in sunpro white gauges 'cause their easier to read. Also, PO painted the panel white and look good in it.

Long story to say I paid $56 for mine (plus shipping) only to break part of the plastic and decide I don't want it.

Whats a broken bezel with good gauges and good plastic faces go for?

FRENCHBLUE72 · 03-29-2004, 11:14 PM

Damn I need to read the headder???

Longhorn Man · 03-30-2004, 12:25 AM

you can get a fresh shiney new bezel for 25 bucks, so don't think of your panel as junk. They can bring quite a bit on e-bay with a tack inthere. (about twice what you'll get for it on here)

Lobo'74 · 03-30-2004, 09:31 AM

I need to read better too. Mine is the non-tach unit with gauges.
Where can I get a new bezel for $25, all the ones I see are running $60 - $80?

*Gee_Emm* · 03-30-2004, 11:07 AM

Apparently you are better off spending more money for a bezel, the $25 ones don't fit too well.

Longhorn Man · 03-30-2004, 06:51 PM

I've bought 4 or 5 of the 25 dollar ones from Ricks I think, and they fit almost perfect. I give them a 95% in fitment.

*Gee_Emm* · 03-30-2004, 08:29 PM

I was looking at one in a store a couple weeks ago and noticed that it was bowed in the middle instead of the whole thing being flat, that kinda turned me off of the cheapies.

Longhorn Man · 03-31-2004, 07:52 AM

These ones were flat.
It's been a year since I've messed with one, but if memory serves, there was a slight fitment issue on the top (back side) I think a screw didn't line up or something.

03-29-2004, 08:51 PM	#1
67chevy2wd Registered User Join Date: Sep 2003 Location: New Salem, ND Posts: 1,558	Guage bezel w/ Tach I have a Gauge Bezel with all the guages except the Vacum guage. I was just wondering if it is worth anything, also it is original and everything works.

03-29-2004, 08:57 PM	#2
SWEET7T Try spinnin 4 rear tars Join Date: Sep 2003 Location: Salt Lake City, Utah Posts: 757	I will swap you a fresh $20 for it!!! Actually, depending on how nice it is, could be worth $100+ __________________ SWEET7T 1970 C10, 2wd, LB, 307/TH350/3.08. PS, PB

03-29-2004, 10:10 PM	#3
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Does it have a tach??? __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

03-29-2004, 10:14 PM	#4
bouncytruck SKINNY TIRES RULE! Join Date: Sep 2001 Location: Bothell, WA Posts: 11,038	Is it a 6 or 8 cyl tach? It should be stamped on the back of the tach. Value also depends on the condition (obviously). Is there any rust on the gauges, faded paint, scratches in the lens, etc. __________________ bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L

03-29-2004, 10:16 PM	#5
Lobo'74 Registered User Join Date: Nov 2002 Location: Charlottesville, VA Posts: 404	Have, er..."had" one I found a '67-'68 gages panel on e-bay and got it for about $56. Didn't have chrome, the gages all look fine. It fell off the box for my truck parts in the garage to the cement floor this winter. Only about a foot, but it hit on the upper right hand corner and broke the plastic bezel there. I've decided I like the non gauge dash the PO cut 2" holes in to mount gages. I've put in sunpro white gauges 'cause their easier to read. Also, PO painted the panel white and look good in it. Long story to say I paid $56 for mine (plus shipping) only to break part of the plastic and decide I don't want it. Whats a broken bezel with good gauges and good plastic faces go for? __________________ "Truck" '67 small window '79 350 .030 over, LT1 "clone"

03-29-2004, 11:14 PM	#6
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Damn I need to read the headder??? __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

03-30-2004, 12:25 AM	#7
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	you can get a fresh shiney new bezel for 25 bucks, so don't think of your panel as junk. They can bring quite a bit on e-bay with a tack inthere. (about twice what you'll get for it on here)

03-30-2004, 09:31 AM	#8
Lobo'74 Registered User Join Date: Nov 2002 Location: Charlottesville, VA Posts: 404	Duhhh I need to read better too. Mine is the non-tach unit with gauges. Where can I get a new bezel for $25, all the ones I see are running $60 - $80? __________________ "Truck" '67 small window '79 350 .030 over, LT1 "clone"

03-30-2004, 11:07 AM	#9
Gee_Emm Account Suspended Join Date: Sep 2000 Posts: 3,991	Apparently you are better off spending more money for a bezel, the $25 ones don't fit too well.

03-30-2004, 06:51 PM	#10
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	I've bought 4 or 5 of the 25 dollar ones from Ricks I think, and they fit almost perfect. I give them a 95% in fitment.

03-30-2004, 08:29 PM	#11
Gee_Emm Account Suspended Join Date: Sep 2000 Posts: 3,991	I was looking at one in a store a couple weeks ago and noticed that it was bowed in the middle instead of the whole thing being flat, that kinda turned me off of the cheapies.

03-31-2004, 07:52 AM	#12
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	These ones were flat. It's been a year since I've messed with one, but if memory serves, there was a slight fitment issue on the top (back side) I think a screw didn't line up or something.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.