|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-07-2017, 02:18 PM
|
#1 |
|
Senior Member
 Join Date: Oct 2010
Location: Zavalla, TX
Posts: 415
|
1972 SWB Drive Shaft Length.
Hi all, I am sure this has been discussed many times. I have a 1972 SWB with a 400 sbc and turbo 350 (short tail shaft) I have a 2 pc drive shaft to go in it. But a friend knows of 1 piece driveshaft the owner sears came out of a 1972 6cyl 3 speed. Was wondering if anyone might know what the length should be on a drive shaft, center to center of the ujoints?
Thanks Eddie |
|
|
|
02-07-2017, 04:25 PM
|
#2 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: 1972 SWB Drive Shaft Length.
in this case cit is far better for you to get under the truck and measure what you need to get the right measurement
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
02-07-2017, 06:18 PM
|
#3 |
|
Senior Member
Join Date: Jun 2005
Location: Winona Lake, IN
Posts: 6,352
|
Re: 1972 SWB Drive Shaft Length.
Which frame holes are your engine stands bolted to, front or rear?
__________________
70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear |
|
|
|
|
02-08-2017, 12:53 AM
|
#4 |
|
Registered User
Join Date: Dec 2016
Location: Brentwood, North California
Posts: 80
|
Re: 1972 SWB Drive Shaft Length.
1968 c10 swb
SBC 350 on the front mounts Turbo 350 short tail 59.25 driveshaft |
|
|
|
|
02-12-2017, 03:56 AM
|
#5 |
|
Registered User
Join Date: Nov 2016
Location: Denver CO.
Posts: 19
|
Re: 1972 SWB Drive Shaft Length.
I had to have my drive shaft lengthened by 4 inches when I did my 6 cylinder to 350 swap, but I kept my 3 speed manual transmission. This is using the forward mounting holes for the v8.
|
|
|
|
|
02-12-2017, 10:37 AM
|
#6 | |
|
Registered User
Join Date: Apr 2012
Location: Ocala,Fl
Posts: 733
|
Re: 1972 SWB Drive Shaft Length.
You really should measure. Mine is 350 on front mounts/700r4/ 55 9/16 shaft. All I had was the trans yoke and it cost me 230 out the door for new one.
__________________
._____________ ..\ .___ . . . . _ . .\. . . . . . . . . . . ___ ..| /_+_/ ___ |o| ...}. . . . . ______i__!\____ . [_____(O)_|_'|__}>-------[-_(O)__i'___i (O)-] Quote:
|
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
