|
02-14-2017, 09:34 PM | #1 |
BMW & ASE Master Certified
Join Date: Feb 2004
Location: Houston, Texas
Posts: 1,257
|
Re: LT1 GenV swap
And more searching revealed the ecu terminals, and most of the connector terminals in the harness.. gonna repair the one the first junk yard nipped off 2 sensors and make it good as new without splices and maybe just run that harness and sell the other harness that's not been damaged.
__________________
1987 Silverado - L83 5.3 w/ 6L80e ,A/C,P/W,P/L,TILT, HID projectors, Wilwood C-10 Pro Spindles w/ 2018 silverado front brakes & C-5 Corvette Rear Disc Brakes 1999 BMW 528i - 5.7 LS1 w/ 4l60e, Ford 8.8 IRS w31 spline posi & FX-r projector retrofit New project: 2006 BMW x5 6cyl AWD to L83 6l80e 4wd to 2WD / RWD A poor man buy's it twice finally got my domain name back, 87chevy.com.... site rework in progress Last edited by 87chevy.com; 02-14-2017 at 10:02 PM. |
03-05-2017, 10:19 AM | #2 |
Registered User
Join Date: Oct 2015
Location: Victoria TX
Posts: 40
|
Re: LT1 GenV swap
How deep are you in the wiring? I'm trying to figure out the canbus. As far as I can tell there are 2 circuits needed, 1 for the FPCM and 1 for the trans. Sound right?
Red
__________________
'68 GMC K1500 LWB L83/6l80/NP205 http://67-72chevytrucks.com/vboard/s...90#post7856190 |
03-06-2017, 01:16 PM | #3 |
BMW & ASE Master Certified
Join Date: Feb 2004
Location: Houston, Texas
Posts: 1,257
|
Re: LT1 GenV swap
Done with the wiring .. it's just a pass pass through. It goes on to trans, tee off into the trans, then goes out the trans to the one one of the connectors x115 or x125 and that's what will go to the obd port.
__________________
1987 Silverado - L83 5.3 w/ 6L80e ,A/C,P/W,P/L,TILT, HID projectors, Wilwood C-10 Pro Spindles w/ 2018 silverado front brakes & C-5 Corvette Rear Disc Brakes 1999 BMW 528i - 5.7 LS1 w/ 4l60e, Ford 8.8 IRS w31 spline posi & FX-r projector retrofit New project: 2006 BMW x5 6cyl AWD to L83 6l80e 4wd to 2WD / RWD A poor man buy's it twice finally got my domain name back, 87chevy.com.... site rework in progress |
03-07-2017, 08:39 PM | #4 |
Registered User
Join Date: Oct 2015
Location: Victoria TX
Posts: 40
|
Re: LT1 GenV swap
Sweet that the way I was gonna wire it. Did you put a resistor in it? Also, the brake pedal switch, are you using the 4 pin switch?
Red
__________________
'68 GMC K1500 LWB L83/6l80/NP205 http://67-72chevytrucks.com/vboard/s...90#post7856190 |
03-08-2017, 02:46 PM | #5 |
BMW & ASE Master Certified
Join Date: Feb 2004
Location: Houston, Texas
Posts: 1,257
|
Re: LT1 GenV swap
Resistor for the can line, yeah. Brake pedal sensor no, gonna try something else.
__________________
1987 Silverado - L83 5.3 w/ 6L80e ,A/C,P/W,P/L,TILT, HID projectors, Wilwood C-10 Pro Spindles w/ 2018 silverado front brakes & C-5 Corvette Rear Disc Brakes 1999 BMW 528i - 5.7 LS1 w/ 4l60e, Ford 8.8 IRS w31 spline posi & FX-r projector retrofit New project: 2006 BMW x5 6cyl AWD to L83 6l80e 4wd to 2WD / RWD A poor man buy's it twice finally got my domain name back, 87chevy.com.... site rework in progress |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|