|
09-01-2017, 02:45 PM
|
#1 |
|
Registered User
Join Date: Feb 2017
Location: Houston tx
Posts: 117
|
Screws
Where can I get the screws to secure the cowl hood as a set or what size are they. Thanks in advance
|
|
|
|
09-01-2017, 03:14 PM
|
#2 |
|
20' Daredevil (Ret)
 
Join Date: May 2003
Location: Jefferson State
Posts: 13,722
|
Re: Screws
Are these what you are looking for?
http://www.classicparts.com/1967-72-...info/38%2D173/ http://www.classicparts.com/1967-72-...info/38%2D159/
__________________
- Mike - 1972 K20 LWB 350/350/205 RIP El Jay |
|
|
|
|
09-01-2017, 06:47 PM
|
#3 |
|
Senior Member
Join Date: Feb 2009
Location: Northern Nevada
Posts: 7,322
|
Re: Screws
The size of the tap screws is debatable. Personally I believe they're a large #8 or small #10. I would start with #8, which is what I believe the part houses offer anyway. Keep that in mind as you read the following:
The panel mounts onto the cowl using six phillips tap screws with integrated washers. The screw threads are #10" x 5/8". These screws also hold the cowl seal in place. The panel also mounts to the cowl using four phillips stainless steel tap screws & U-nuts."" The screw threads are #10 x 1/2". The holes for these are nearly parallel of the windshield wiper mounts. The U-nuts are 1/2" x 5/8, and the hole center to edge is 1/2"". The panel also mounts using four 1/2" recessed hex head tapered screws with integrated washers. One fits behind each door, and one on each corner of the cowl. The threads on three of these screws are 5/16-18 x 7/8. The thread on one screw is 5/16-18 x 3/4. The shortest thread was used behind the RH door, which probably means nothing. 3/4" or 7/8" should work. Also, they don't have to be tapered. They just happened to be on the truck I'm rebuilding.
__________________
Tony 71 Custom Deluxe, SWB, 2WD, 402, A/C. I developed an assembly kit for restoring the (a) truck from the ground up. My build thread, and more on the assembly kit https://67-72chevytrucks.com/vboard/...d.php?t=730025 Last edited by 71CHEVYSHORTBED402; 09-02-2017 at 01:42 AM. |
|
|
|
|
09-01-2017, 07:24 PM
|
#4 |
|
Registered User
Join Date: Feb 2017
Location: Houston tx
Posts: 117
|
Re: Screws
Thanks for the info. Best site for our c10s.
|
|
|
|
|
09-01-2017, 11:18 PM
|
#5 |
|
Carpe manana
  
Join Date: Dec 2010
Location: Eau Claire, WI
Posts: 12,443
|
Re: Screws
Here's a reference pic if helpful: http://67-72chevytrucks.com/vboard/s...2&postcount=58
__________________
1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308  Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland
|
|
|
|
|
09-02-2017, 12:43 AM
|
#6 |
|
Senior Member
Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,852
|
Re: Screws
Another reference. These are originals.
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
