|
01-04-2018, 11:41 AM
|
#1 |
|
Registered User
Join Date: Jul 2017
Location: Indian Harbour Beach, Florida
Posts: 5
|
Getting a tune up
Hey everyone, I recently purchased a 72 c10 with a '77 350 small block, I am going to get some parts for her first tune up at her new home any suggestions on brands/performance for the cap, points, plugs, etc? Thank You.
|
|
|
|
01-04-2018, 11:49 AM
|
#2 | ||||
|
"I ain't nobody, dork."
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,971
|
Re: Getting a tune up
Your local parts house will have everything you need. If you have a Napa, go there. NGK or AC Delco plugs.
Gary
__________________
'cuz chicks dig scars... My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread. The Rebuild of Creeping Death after the wreck Quote:
Quote:
Quote:
Quote:
|
||||
|
|
|
|
01-04-2018, 01:24 PM
|
#3 |
|
20' Daredevil (Ret)
 
Join Date: May 2003
Location: Jefferson State
Posts: 13,722
|
Re: Getting a tune up
FWIW, the only plugs I ever had bad luck with were Champions, the one time I ran them. I usually run AC plugs, and once had *cough* Motorcrafts (don't ask) which worked fine.
__________________
- Mike - 1972 K20 LWB 350/350/205 RIP El Jay |
|
|
|
|
01-04-2018, 02:21 PM
|
#4 |
|
Registered User
Join Date: Jan 2011
Location: Chattanooga, TN
Posts: 2,165
|
Re: Getting a tune up
I would use AC Delco for plugs and wires. Blue Streak for cap, rotor, points, and condenser. I have also had great luck with MOROSO wires. I have had very bad luck with many house brand plug wires. So I only use pre-made Delco, Autolite, or MOROSO plug wires.
Or if you swap to an HEI distributor get AC Delco for all of it. Since you want to replace everything, now would be a good time.
__________________
'83 K20-TPI '73 C10 '79 C10-ex-diesel(SOLD) '07 Tahoe(Son driving) '14 Suburban-DD '71 C10-current project |
|
|
|
|
01-04-2018, 04:33 PM
|
#5 |
|
Registered User
Join Date: Jul 2015
Location: 2nd left past the stump on a dirt road.
Posts: 2,629
|
Re: Getting a tune up
Do not forget to clean off your dist advance weights and get a new vac advance if needed. Those advance units go out fairly easily.
Do a search on here, someone did some extensive data acquisition for the vac advance units. Or just go with an adjustable unit from Moroso or Accel. Mikey likes them! |
|
|
|
|
01-04-2018, 09:22 PM
|
#6 |
|
Registered User
Join Date: Jun 2013
Location: Somewhere
Posts: 3,123
|
Re: Getting a tune up
I'd inspect parts before replacing, and run the engine in the dark (at night) w/ the hood open to check for little blue sparks.
To add to the above, a spot of grease on those advance pivot points is nice. 77 would be HEI and small tapered plugs so step one is what do you have? Small plugs means 5/8" hex and tapered means they seal against the head with an angled base. HEI has the coil in the cap. |
|
|
|
|
01-04-2018, 09:51 PM
|
#7 |
|
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,727
|
Re: Getting a tune up
I'd buy a Skip White HEI and convert it. (or your Chinese HEI knockoff of choice.) Comes with all new parts. Buy your choice of wires and don't look back! Fix as needed if you have coil or module failure in the future. I usually keep a spare module in my HEI equipped vehicles.
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
|
|
|
|
01-04-2018, 10:05 PM
|
#8 |
|
Registered User
Join Date: Jul 2015
Location: Smithton, Mo.
Posts: 158
|
Re: Getting a tune up
I would check out Rockauto or Summit if you're not in a hurry. Shipping usually takes a day or two. You can save a fair amount of money. Summit has a good stock of ACDelco parts.
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
