1970 C40 Build

[khess]

Just picked this up this week. Havent really dug into it yet but I know it's a V8 with most of the parts still with it. Trying to figure out what parts cross over from other models since all the parts sites I use go from C30 to C50 and skip this model. Not entirely sure of my plans yet but will update as i go !

[C10 - C90 Bill]

Most C-50 parts should fit your C-40.

Welcome to the site and keep us posted on it.

[khess]

Thanks !

[khess]

Trying to decipher the VIN so I have a better handle on the truck :
CE43DP159114
4x2
V8
??? (4)
Cab and Chassis
1970
Pontiac Plant

Any decoder I've tried to use wont let me since the VIN is too short and most other ones on here are for smaller trucks. If anyone could correct any information that might be wrong that would be great, I've struck out and kind of pieced it together lol

[Robert1970C20rstbukt]

Cool truck, don't see C40's very often. I've only seen one around here, local junkyard had a '69 C40 several years ago. If I could have saved it I would have, but had no extra money back then.

I think the D in your VIN might be a 0:

C Conventional cab 4x2
E V8 gas engine
4 13,5 to 18,000 GVW
3 Chassis Cab
0 1970
P Pontiac plant

[Bob B.]

A C/40 is just a light duty C/50. Many had 250 6's or 307 V-8's, and they were regular light duty pickup truck engines. I think only transmission available was a CH-465. Many were sold with a factory installed 9' or 12' stake bed. Low cost truck for farmers, ect..

[khess]

Thanks for shedding a little more light on the truck. I know it's got a V8 so I'm assuming its the 307 then; Previous owner said it had a 4 speed with a 2 speed rear.

I know the path I want to go with it. It's going to get bags and wheels. Clean it up some. Undecided if I want to toss a modern drive train in it or just keep what's there.

Tossing ideas around for the back half of the truck. Everyone does the stake body, flat bed or something custom. I'll think of something original. I appreciate everyone's comments and help thus far !

[Robert1970C20rstbukt]

Sounds good! My 1970 service manual also lists the light duty 350 with a 2 barrel carb as an option, best bet is to check the casting numbers.

[khess]

It's definitely going to be a learning experience. What I'm gathering is that a lot of the parts from the light duty trucks do transfer over the the c40/c50, If I've read correctly?

[C10 - C90 Bill]

Originally Posted by khess

It's definitely going to be a learning experience. What I'm gathering is that a lot of the parts from the light duty trucks do transfer over the the c40/c50, If I've read correctly?

Some parts from Pick-ups will fit, most parts from a C-50 will fit, it all depends on the part.

By the way, make sure your doors are from a C-50 or C-60. They look the same, but they are different (unless you want to do some modifying).

[khess]

The doors are in the barn on the Previous Owners property. Waiting for the weather to clear up a bit so I can bring her to storage, so i'm only going off what I saw when I was there. VIN # doesn't seem completely right so I'm being patient until I get the truck in my hands to see what I've got.

[khess]

Well Apparently I don't listen very well. The truck does in fact have a 350. The '71 C10 I' might be buying from the same person has the 307. Oops lol

[khess]

I might yank the 350 and put that in my C10..maybe. I do know that this will be getting a fresh and newer drive train (6.0 or 8.1), Air, some big wheels and some sort of bed on the back. A simple cruiser.

[khess]

Craigslist is like my mistress..she makes me do things I normally wouldn't lol

Jumped on a set of these..



24's..

[bigrigpardo]

Nice but what bolt pattern are those? I don't think they are the same as the truck are they?

[khess]

Nope, they're not the same but I'm more than likely going to change up the rear end to something newer, with adapters these will fit just fine.

[Honest Bob]

Kyle!!!!!!

Build a tiny home on the back!

[khess]

oh hi ben ! Super undecided on what i'm doing back there lol

[khess]

I have a second build thread as well ben in the C10 section, if you hop over there lol

[Honest Bob]

I dont normally roam in there but I'll check it out.

[khess]

Can't figure out how to post a for sale thread. But the C40 is for sale.

[maxx442]

You have to be a paying member.

[txagincali]

Originally Posted by khess

Can't figure out how to post a for sale thread. But the C40 is for sale.

What? You just got this thing a month ago didn't you? Why the change of heart?

Let me know if you are willing to part it out (fenders, extensions and steps especially)

[khess]

Taking on another build with my father that's a little more important and the c10 I picked up with this has precedence over this. So, instead of sitting on it I'd rather see someone else enjoy it. That's all lol