06 GTO alternator and brackets - The 1947 - Present Chevrolet & GMC Truck Message Board Network

short71 · 03-23-2018, 01:21 PM

I have been gathering all my parts and reading everything I can before my swap starts in a couple weeks. I have an 06 GTO ls2 with transmission. Going into a 71 c10 swb. When ordering mounts they say they do not clear the lower alternator bracket? Question is can I modify the mounts to move it slightly? Do I have to get a bracket to move to the top? And if so is there a cost effective mount? Also is the spacing on the GTO assembly the same as the Corvette or is it different? Or is it a matter of notching to make it fit?.. so far I think I have figured out a lot of it but I'm sure I'll have more questions as the swap gets started. Thanks for all the help this group has been so far by posting!

71cadc10 · 03-25-2018, 02:51 PM

the spacing is same as 4th gen Fbody, not corvette.

I'm doing the same type of thing...06 gto engine /t56 and harness going in.
I'm struggling with the alt now..it won't clear the engine mounts down low driver side where the stock bracket puts it. If you are willing to fab up your own engine mount/stand on the driver side I'm sure something can be made to work.

I'm planning to run truck pulley and front accessory setup, since I have both them and the GTO...mount a truck alt up high driver side. converting to 1 wire hookup on a truck alt.
The 06 computer is E40 and has alt control in the PCM...so the GTO alt is a fairly uncommon piece.

Ghost's68 · 03-25-2018, 03:30 PM

I’m running the CPP stands and DD sliders with my swap. A lot of people had issues with the Camaro low mount Alt not working. I had no issues, I gen bought the Holley Alt relocation kit thinking I would have to go that route. But to my surprise mine tucked in nice into the frame rails.

71cadc10 · 03-25-2018, 03:52 PM

Ghost, to clarify from looking at your pic, that is a gen V camaro alt and bracket looks like 2010+ or is it 4th gen stuff ?

**dayj1** · 03-25-2018, 10:41 PM

Quote:

Originally Posted by short71

I have been gathering all my parts and reading everything I can before my swap starts in a couple weeks. I have an 06 GTO ls2 with transmission. Going into a 71 c10 swb. When ordering mounts they say they do not clear the lower alternator bracket? Question is can I modify the mounts to move it slightly? Do I have to get a bracket to move to the top? And if so is there a cost effective mount? Also is the spacing on the GTO assembly the same as the Corvette or is it different? Or is it a matter of notching to make it fit?.. so far I think I have figured out a lot of it but I'm sure I'll have more questions as the swap gets started. Thanks for all the help this group has been so far by posting!

I used a camaro/gto low mount alternator bracket on a 4.8 swap into a 72 c10 with no clearance issues. I just used adapter plates on stock v8 towers. I made my own adapter plates on that one, but they're not unlike generic adapters available on ebay and the like.

short71 · 03-26-2018, 06:22 PM

Thank you guys. I'll post up what I had to do to get it in. Looking like I'll test fit and go from there.

03-23-2018, 01:21 PM	#1
short71 Registered User Join Date: Jun 2017 Location: Vancouver Posts: 14	06 GTO alternator and brackets I have been gathering all my parts and reading everything I can before my swap starts in a couple weeks. I have an 06 GTO ls2 with transmission. Going into a 71 c10 swb. When ordering mounts they say they do not clear the lower alternator bracket? Question is can I modify the mounts to move it slightly? Do I have to get a bracket to move to the top? And if so is there a cost effective mount? Also is the spacing on the GTO assembly the same as the Corvette or is it different? Or is it a matter of notching to make it fit?.. so far I think I have figured out a lot of it but I'm sure I'll have more questions as the swap gets started. Thanks for all the help this group has been so far by posting!

03-25-2018, 02:51 PM	#2
71cadc10 Registered User Join Date: Apr 2004 Location: Boiling Springs, PA Posts: 435	Re: 06 GTO alternator and brackets the spacing is same as 4th gen Fbody, not corvette. I'm doing the same type of thing...06 gto engine /t56 and harness going in. I'm struggling with the alt now..it won't clear the engine mounts down low driver side where the stock bracket puts it. If you are willing to fab up your own engine mount/stand on the driver side I'm sure something can be made to work. I'm planning to run truck pulley and front accessory setup, since I have both them and the GTO...mount a truck alt up high driver side. converting to 1 wire hookup on a truck alt. The 06 computer is E40 and has alt control in the PCM...so the GTO alt is a fairly uncommon piece. __________________ 71 C10 long bed, 2003 6.0L, 06GTO E40, T56, 12bolt 4.10 rear

03-25-2018, 03:30 PM	#3
Ghost's68 Registered User Join Date: Jun 2016 Location: American Canyon, CA Posts: 253	Re: 06 GTO alternator and brackets I’m running the CPP stands and DD sliders with my swap. A lot of people had issues with the Camaro low mount Alt not working. I had no issues, I gen bought the Holley Alt relocation kit thinking I would have to go that route. But to my surprise mine tucked in nice into the frame rails.

03-25-2018, 03:52 PM	#4
71cadc10 Registered User Join Date: Apr 2004 Location: Boiling Springs, PA Posts: 435	Re: 06 GTO alternator and brackets Ghost, to clarify from looking at your pic, that is a gen V camaro alt and bracket looks like 2010+ or is it 4th gen stuff ? __________________ 71 C10 long bed, 2003 6.0L, 06GTO E40, T56, 12bolt 4.10 rear

03-26-2018, 06:22 PM	#6
short71 Registered User Join Date: Jun 2017 Location: Vancouver Posts: 14	Re: 06 GTO alternator and brackets Thank you guys. I'll post up what I had to do to get it in. Looking like I'll test fit and go from there.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.