Window division bar felt question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Fbks_Cruiser** · 05-03-2019, 11:08 PM

I recently purchased the 8 piece door window seal kit from GMC Pauls. Before I start pulling out my old seals I thought I should ask about my division bar. It appears to have some stainless trim along the edges. The one on the inside of the passenger door is damaged as you can see in the picture. Is this part of the felt and will just go away when I remove the old or is it actually part of the division bar? The new division bar felts I got do not have any stainless edging. Do I need it? If so can it be fixed without replacing the whole division bar?

**Grumpy old man** · 05-03-2019, 11:18 PM

stainless trim goes all the way to the bottom pull it off and forget about it . Really needs to be replaced about $30.00

**Fbks_Cruiser** · 05-03-2019, 11:25 PM

Thanks. I assumed it was just added trim and not essential but wanted to make sure it didn’t serve to help secure the felt before I started taking it out.

RustyPile · 05-04-2019, 01:25 PM

Here's a link to replacement division bars..

https://www.classicparts.com/1955-59...ctinfo/03-461/

**Fbks_Cruiser** · 05-04-2019, 01:55 PM

Thanks. I’ll keep those in mind.

05-03-2019, 11:08 PM	#1
Fbks_Cruiser Senior Member Join Date: Apr 2016 Location: Fairbanks, AK Posts: 343	Window division bar felt question I recently purchased the 8 piece door window seal kit from GMC Pauls. Before I start pulling out my old seals I thought I should ask about my division bar. It appears to have some stainless trim along the edges. The one on the inside of the passenger door is damaged as you can see in the picture. Is this part of the felt and will just go away when I remove the old or is it actually part of the division bar? The new division bar felts I got do not have any stainless edging. Do I need it? If so can it be fixed without replacing the whole division bar? Attached Images __________________ 1972 GMC K2500 Super Custom Matt

05-03-2019, 11:18 PM	#2
Grumpy old man Senior Member Join Date: Dec 2013 Location: Gods country East,Tn Posts: 8,545	Re: Window division bar felt question stainless trim goes all the way to the bottom pull it off and forget about it . Really needs to be replaced about $30.00 __________________ 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop

05-03-2019, 11:25 PM	#3
Fbks_Cruiser Senior Member Join Date: Apr 2016 Location: Fairbanks, AK Posts: 343	Re: Window division bar felt question Thanks. I assumed it was just added trim and not essential but wanted to make sure it didn’t serve to help secure the felt before I started taking it out. __________________ 1972 GMC K2500 Super Custom Matt

05-04-2019, 01:25 PM	#4
RustyPile Registered User Join Date: Dec 2017 Location: Elkhart, Texas Posts: 1,841	Re: Window division bar felt question Here's a link to replacement division bars.. https://www.classicparts.com/1955-59...ctinfo/03-461/

05-04-2019, 01:55 PM	#5
Fbks_Cruiser Senior Member Join Date: Apr 2016 Location: Fairbanks, AK Posts: 343	Re: Window division bar felt question Thanks. I’ll keep those in mind. __________________ 1972 GMC K2500 Super Custom Matt

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.