|
06-08-2004, 09:49 AM
|
#1 |
|
Registered User
Join Date: Jan 2004
Location: Walker,louisiana
Posts: 179
|
header ?
i have a 70 swb fleetside with a smb 350 . what headers are you guys useing to keep the pipes up in the frame mine hang really low .
__________________
(If all else fails get a bigger hammer) |
|
|
|
06-08-2004, 11:08 AM
|
#2 |
|
Thats the Hillbilly way
Join Date: Jul 2001
Location: Torrance,Ca
Posts: 5,979
|
I run the Dynomax Cerama-coat headers , on BB they don't hang too low .
Here is an old Pic .
__________________
BILL Torrance Calif 90504 Member DUF Club Member Old Farts Club 72 3/4ton Custom Camper BB402/400 trans Dynomax Cerama-coat headers , Hei distributor ,Edelbrock 1411 air,ps,pb,leafsprings ,98 chevy 60/40 seat,S10 shoulder belts tilt,3.54 Dana 60 rear. 16" Eagle wheels with LT265/75 16 tires,Gaylord Lid,H4 headlights with 100W relay conversion. " If I knew I was going to live this long I would have taken better care of myself " Marriage changes passion...suddenly you're in bed with a relative. A GUY'S PRAYER.... Lord, I pray for a nympho with huge boobs who owns a liquor store and likes to fish and hunt and has a Harley .Amen , |
|
|
|
|
06-09-2004, 02:03 AM
|
#3 |
|
Registered User
Join Date: Nov 2002
Location: Kelowna B.C. Canada
Posts: 1,086
|
Ive got an old set of Blackjacks they hang a bit low but I'm not into lowering my truck and my starter likes em also (no shield). Hey Bill72BB How is the ceramic coating holding up? Is the truck in the pic your driver? Thanks Doug
|
|
|
|
|
06-09-2004, 08:08 AM
|
#4 |
|
Registered User
Join Date: Jan 2004
Location: NH
Posts: 2,266
|
I was using a set of Dynomax like Bill and highly recomend them, after 7yrs they held up well and had no real issues installing plugs. Getting the ceramic coated is also a plus in keeping the heat down in the engine compartment and hold their looks far better than any plain steel headers that rust up usually in no time.
__________________
1967 C10 - SWBSS Pro Street 427sbc, 700R4 & 4.10 Gears 1948 Chevy FleetMaster Coupe, LS1, (almost done) 1950 Chevy StyleLine Coupe 250/6 3x2 Dueces 2009 Toyota Tundra 1996 Harley RoadKing "I maybe getting old, but I can still burn rubber with the best of them" |
|
|
|
|
06-09-2004, 10:00 AM
|
#5 | |
|
Thats the Hillbilly way
Join Date: Jul 2001
Location: Torrance,Ca
Posts: 5,979
|
Quote:
The truck is my daily driver but looks like this now.
__________________
BILL Torrance Calif 90504 Member DUF Club Member Old Farts Club 72 3/4ton Custom Camper BB402/400 trans Dynomax Cerama-coat headers , Hei distributor ,Edelbrock 1411 air,ps,pb,leafsprings ,98 chevy 60/40 seat,S10 shoulder belts tilt,3.54 Dana 60 rear. 16" Eagle wheels with LT265/75 16 tires,Gaylord Lid,H4 headlights with 100W relay conversion. " If I knew I was going to live this long I would have taken better care of myself " Marriage changes passion...suddenly you're in bed with a relative. A GUY'S PRAYER.... Lord, I pray for a nympho with huge boobs who owns a liquor store and likes to fish and hunt and has a Harley .Amen , |
|
|
|
|
|
06-09-2004, 11:42 AM
|
#6 |
|
Registered User
Join Date: Mar 2000
Location: Olalla, WA
Posts: 705
|
I use Hooker supercomp in my 2wd stepside (auto) and Hooker Compitition in my 72 Blazer 4wd (4 speed). They both are great fits and I highly recommend them. I have used the Flowtech and some other brand that hung way too low and would bottom out on my stepside. After I put the hookers in, there is no chance of draging and I never had a header that fit in so easy. Here is a picture of the headers on my stepside.
Chap
__________________
This is only my opinion and it is subject to change. 70 GMC Short box stepside Blown 388 Stroker 72 K/5 Blazer 350/SM465/205 |
|
|
|
|
06-09-2004, 03:49 PM
|
#7 |
|
Registered User
Join Date: Nov 2002
Location: Kelowna B.C. Canada
Posts: 1,086
|
Thanks Bill, Very Sharp Truck Also!
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
