TN 250 6 engines and parts - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Grumpy old man** · 06-30-2017, 07:09 AM

Quote:

Originally Posted by Beetle

Grumpy, I will have a 250 PS setup available here soon. I am about to pull my 250 6 out. What would you need? Check my build thread the second one down in red for pics. PM me if you want. I ain't lookin to get rich off the stuff, just know there's folks out there that need it.

Pm sent , thanks I'm always looking .

**Grumpy old man** · 06-30-2017, 12:18 PM

Quote:

Originally Posted by 70shortstep

Any chance you have one of these?

I found your parts and pulled them for you PM me a phone number to send pictures to . I was using photobucket and now I have to find a different way to past pictures

70shortstep · 06-30-2017, 01:14 PM

Pm sent. Thanks

**slepysal** · 07-12-2017, 05:10 PM

Looking for the manifold hold down clamps Ca 95112

ElCoSix · 06-11-2018, 07:15 PM

Hi,
I have a 67 El Camino with a 250 that I'm restoring. The bolt is broken in the front of the crankshaft. I know it wouldn't be the biggest sale you ever made, but do you have one of those bolts - or do you know the thread size and thread pitch? I'm trying to get the broken bolt out and running out of ideas, but if I can figure out the exact thread size and pitch maybe I can at least clean out some of the threads near the top of the hole with a thread chaser, and that would get me to the next step. (If I can get a bolt started and stable enough I'm thinking maybe a machine shop could drill down the center of the good bolt so I can use it as a drill guide. That way I can get a good, centered pilot hole drilled and maybe then have better luck using an extractor or even a reverse direction drill bit.
I'm really hoping I don't have to tear it apart to get this done.
Thanks a lot for any advice or help you can give me.
Scott

**70STOVEBOLT** · 06-12-2018, 01:04 PM

250's dont have a crank bolt. The damper presses on.

jfnar · 06-12-2018, 03:45 PM

I don't know if this even exists but I'm looking for a three groove water pump pulley that matches the groove spacing on my 292 balancer. The gap between the front and middle grooves is a little bigger than the gap between the middle and back grooves. Thanks.

**70STOVEBOLT** · 06-12-2018, 04:41 PM

Never seen a 3-groove water pump pulley. A 250 pulley is different than a 292 pulley though.

rdhowe2006@yahoo.com · 03-05-2020, 04:51 PM

I am in need of a IL 6 Cylinder 230 or 250?

06-30-2017, 01:14 PM	#53
70shortstep Registerd User Join Date: Nov 2006 Location: Little Rock,AR Posts: 220	Re: 250 6 engines and parts Pm sent. Thanks __________________ John My build thread http://67-72chevytrucks.com/vboard/s...d.php?t=613398

07-12-2017, 05:10 PM	#54
slepysal Registered User Join Date: Oct 2006 Location: San Jose NOR*CAL Posts: 3,080	Re: 250 6 engines and parts Looking for the manifold hold down clamps Ca 95112 __________________ 1960 Apache long bed fleet L6 250 Clifford intake 2 bbl carb. Langdon cast headers with dual exhaust and bellflower tips. T-5 5 speed, power steering and power disc brakes. "Over, Around or through it... "

06-11-2018, 07:15 PM	#55
ElCoSix Registered User Join Date: Jun 2018 Location: Los Angeles CA Posts: 7	Re: 250 6 engines and parts Hi, I have a 67 El Camino with a 250 that I'm restoring. The bolt is broken in the front of the crankshaft. I know it wouldn't be the biggest sale you ever made, but do you have one of those bolts - or do you know the thread size and thread pitch? I'm trying to get the broken bolt out and running out of ideas, but if I can figure out the exact thread size and pitch maybe I can at least clean out some of the threads near the top of the hole with a thread chaser, and that would get me to the next step. (If I can get a bolt started and stable enough I'm thinking maybe a machine shop could drill down the center of the good bolt so I can use it as a drill guide. That way I can get a good, centered pilot hole drilled and maybe then have better luck using an extractor or even a reverse direction drill bit. I'm really hoping I don't have to tear it apart to get this done. Thanks a lot for any advice or help you can give me. Scott

06-12-2018, 01:04 PM	#56
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,266	Re: 250 6 engines and parts 250's dont have a crank bolt. The damper presses on. __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Power windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear

06-12-2018, 03:45 PM	#57
jfnar Registered User Join Date: Jul 2009 Location: Jonesboro, AR Posts: 410	Re: 250 6 engines and parts I don't know if this even exists but I'm looking for a three groove water pump pulley that matches the groove spacing on my 292 balancer. The gap between the front and middle grooves is a little bigger than the gap between the middle and back grooves. Thanks.

06-12-2018, 04:41 PM	#58
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,266	Re: 250 6 engines and parts Never seen a 3-groove water pump pulley. A 250 pulley is different than a 292 pulley though. __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Power windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear

03-05-2020, 04:51 PM	#59
rdhowe2006@yahoo.com Registered User Join Date: May 2016 Location: Summit, MS. Posts: 188	Re: 250 6 engines and parts I am in need of a IL 6 Cylinder 230 or 250?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.