|
09-04-2020, 07:46 AM
|
#1 |
|
Senior Member
 
Join Date: Jun 2007
Location: Pine Ridge Florida
Posts: 4,135
|
Stainless exhaust
Has anyone used or can anyone recommend 1 of the stainless steel exhaust kits they sell.I want to install it on my blazer after the LS3 is installed.I know I may have to shorten it for the blazer but it will still be cheaper than having a complete custom exhaust system made out of stainless.So does anyone have any experience with the stainless steel kits for sale
Thanks Mark
__________________
Click on my Not really a build thread, yet NOT SO RUST FREE RUST FREE BLAZER LS ENGINE SWAP INFORMATION THREAD BOLT RESTORATIONS 4l60 to an NP205 |
|
|
|
09-04-2020, 04:15 PM
|
#2 |
|
Senior Member
Join Date: Jun 2005
Location: Winona Lake, IN
Posts: 6,424
|
Re: Stainless exhaust
I used a Pypes SGT79 kit but I modified it to run inside the frame rails instead of under the frame. I am very happy with the quality and fit. It came with an x-pipe but I did not have room for it, as I put electric cutouts on it.
__________________
70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear |
|
|
|
|
09-04-2020, 04:51 PM
|
#3 |
|
Senior Member
Join Date: Jun 2007
Location: Pine Ridge Florida
Posts: 4,135
|
Re: Stainless exhaust
Do they have a website? I can find them for sale everywhere but not the manufacturers website.
Thanks
__________________
Click on my Not really a build thread, yet NOT SO RUST FREE RUST FREE BLAZER LS ENGINE SWAP INFORMATION THREAD BOLT RESTORATIONS 4l60 to an NP205 |
|
|
|
|
09-04-2020, 07:03 PM
|
#4 |
|
Registered User
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
|
Re: Stainless exhaust
I have used Magnaflow I really liked the kit went on my camaro z28 like a glove
one thing I noted is you need to tack weld the joints if using a walker style band clamp to help hold everything in place When I get to this stage with my truck i will seriously consider going magnaflow again it was well built with no need of getting things re bent to fit Lol fuel economy went down in the camaro in town flaying with the throttle to hear the lovely sound |
|
|
|
|
09-08-2020, 08:28 AM
|
#5 | |
|
Senior Member
Join Date: Jun 2005
Location: Winona Lake, IN
Posts: 6,424
|
Re: Stainless exhaust
Quote:
__________________
70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear |
|
|
|
|
|
09-08-2020, 09:24 AM
|
#6 |
|
Almost Satisfied
 
Join Date: Mar 2002
Location: Springfield, MO
Posts: 2,932
|
Re: Stainless exhaust
I just purchased the Hooker Blackheart system for LS swapped C10's. It fits perfect on the coil truck. Not sure what mods you would have to make for the Blazer. It runs in the frame. Trying to get it hooked up to the headers now, but otherwise it is a very simple kit.
__________________
1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far." |
|
|
|
|
09-08-2020, 09:30 AM
|
#7 | |
|
Senior Member
Join Date: Jun 2007
Location: Pine Ridge Florida
Posts: 4,135
|
Re: Stainless exhaust
Quote:
__________________
Click on my Not really a build thread, yet NOT SO RUST FREE RUST FREE BLAZER LS ENGINE SWAP INFORMATION THREAD BOLT RESTORATIONS 4l60 to an NP205 |
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
