The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-15-2020, 08:18 PM   #1
03BlkZ
Registered User
 
Join Date: Nov 2015
Location: Hewitt, Tx
Posts: 386
Header and Exhaust question

As my build progresses I am now looking at a set of headers for my 350. I want them just for the look mainly and decided not to do long tunes because I hear they hang low. What mid length or shorty headers are everyone running? Also my truck is a 3 on the tree.

Next question is my truck has a 2.5 inch front and 4 inch rear drop. If I buy an exhaust system will they work on my lowered truck? I'm looking for bolt in with some headers. I didn't know if I would need custom exhaust with my drop.
Thanks
03BlkZ is offline   Reply With Quote
Old 10-15-2020, 08:43 PM   #2
Ziegelsteinfaust
Registered User
 
Join Date: Dec 2012
Location: Temple City
Posts: 3,623
Re: Header and Exhaust question

I know on the later trucks using car long tubes tuck them up nicely. Which should be the same on your year as our frames are very similar.

Mid tubes 1 7/8's are not a bad choice, but I would prefer one tubes for the work myself.

The drop your describing only effects exhaust choices in 2 ways. If the headers hand to far down. You will bounce them off the truck. Or you may not be able to do a over the axle system due to lack of clearance there. Other then that a normal tuck job works fine.

I had a 5/7 drop with long tubes on a 74, and had no issues. Except I had it dump in front of the axle.
Ziegelsteinfaust is offline   Reply With Quote
Old 10-17-2020, 08:58 AM   #3
special-K
Special Order

 
special-K's Avatar
 
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,852
Re: Header and Exhaust question

You can't use 3/4 length car headers on a manual transmission is the only thing. Those headers run right through where the clutch linkage is. The right fitting full length header will be fine with your 2.5" drop. The thing to look for is the LH back tube runs straight down or slightly forward to meet with the other pipes down below. The linkage is behind that vertical line.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed"

GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project)
GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling)
Tim

"Don't call me a redneck. I'm a rough cut country gentleman"

R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~
special-K is offline   Reply With Quote
Old 10-17-2020, 09:31 AM   #4
68 P.O.S.
Registered User
 
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
Re: Header and Exhaust question

Get good, quality headers. If you buy cheap $99 specials, you'll hate them. Good quality headers aren't cheap.

https://www.summitracing.com/parts/dou-d371y
__________________
72 C10 lwb fleetside -stock 350/350 combo
68 P.O.S. is offline   Reply With Quote
Old 10-17-2020, 09:45 AM   #5
03BlkZ
Registered User
 
Join Date: Nov 2015
Location: Hewitt, Tx
Posts: 386
Re: Header and Exhaust question

Quote:
Originally Posted by 68 P.O.S. View Post
Get good, quality headers. If you buy cheap $99 specials, you'll hate them. Good quality headers aren't cheap.

https://www.summitracing.com/parts/dou-d371y
Thanks! I will look.into these headers. I know all about header quality. I have run headers on my corvettes for years and I have found you get what you pay for. Kooks or American Racing are the go to for those cars but this is a different animal.
03BlkZ is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:05 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com