NV WTB - looking for Vent Window Parts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**71CHEVYSHORTBED402** · 03-12-2021, 05:43 PM

FOUND WHAT I WAS LOOKING FOR. Didn't know that bar was part of the assembly unit. Thank you.

Discovered why my RH roll up window was so clumsy yesterday, getting T-boned will do that, took us five house to fit the door when the accident first discovered, bent pillar & that.

Good news we feared the door was well plastered, but no, the guys did I nice job pulling out the dent, but they favored bondo over welds for the holes they drilled.

Anyway the vent window is nice less a bent bar and bracket, loose rivets on the bracket. I straightened the bar to a major extent, enough to put the chrome edge back on. It's going in for a tune-up, - either way the bracket has to come off to finish straightening the bar, not a big deal.

1. I'd rather start with a good bracket, so looking for one of those for sure.

2. If it's out there, see the exterior chrome bezel in the picture. I think they're interchangeable left or right. Mine is real good, no pitting etc., better is better

3. Can be talked into the chrome edging for the felt if they're sharp.

4. Or just a vent window with nice parts described above. Thank you.

**Grumpy old man** · 03-12-2021, 08:45 PM

truck shop .

**jaros44sr** · 03-13-2021, 10:53 AM

Quote:

Originally Posted by Grumpy old man

truck shop .

I Google it, but nothing comes up, any other help

**72ironmike** · 03-13-2021, 11:08 AM

Quote:

Originally Posted by jaros44sr

I Google it, but nothing comes up, any other help

http://www.truckandcarshop.com/

**Classic Bowties** · 03-14-2021, 01:53 AM

Hi Tony, we have a pair of NOS division bar felt channel runs available in the below linked "Several GM NOS 67-72 Truck Parts" f/s thread, listed as part/item #19. Have a look if interested in replacing the complete rear of vent wing channel. Mel

http://67-72chevytrucks.com/vboard/s...d.php?t=798288

.

**71CHEVYSHORTBED402** · 03-15-2021, 03:39 PM

Quote:

Originally Posted by Classic Bowties

Hi Tony, we have a pair of NOS division bar felt channel runs available in the below linked "Several GM NOS 67-72 Truck Parts" f/s thread, listed as part/item #19. Have a look if interested in replacing the complete rear of vent wing channel. Mel

http://67-72chevytrucks.com/vboard/s...d.php?t=798288

.

Thanks Mel. Nothing too good for my truck I guess. Kidding, but I should be used to the "surprises" by now. Oh sure, the $1700 improvements on axle & driveline should only run $400 to restore those parts

**Classic Bowties** · 03-15-2021, 09:24 PM

Quote:

Originally Posted by 71CHEVYSHORTBED402

Thanks Mel. Nothing too good for my truck I guess. Kidding, but I should be used to the "surprises" by now. Oh sure, the $1700 improvements on axle & driveline should only run $400 to restore those parts

Tony, payment recieved on the GM NOS division bar felt channel run set from the "Several NOS 67-72 Parts" f/s thread, here is the OE used bracket for mounting bottom end of vent wing felt channel run to inner door. Please note that our paypal acct has been changed as Dec. 2020, new acct info has been returned. Thanks, Mel

.

**71CHEVYSHORTBED402** · 03-15-2021, 11:20 PM

Quote:

Originally Posted by Classic Bowties

Tony, payment recieved on the GM NOS division bar felt channel run set from the "Several NOS 67-72 Parts" f/s thread, here is the OE used bracket for mounting bottom end of vent wing felt channel run to inner door. Please note that our paypal acct has been changed as Dec. 2020, new acct info has been returned. Thanks, Mel

.

Nice bracket Mel, thank you.

03-12-2021, 08:45 PM	#2
Grumpy old man Senior Member Join Date: Dec 2013 Location: Gods country East,Tn Posts: 8,545	Re: WTB - looking for Vent Window Parts truck shop . Attached Images __________________ 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop

03-14-2021, 01:53 AM	#5
Classic Bowties Always on the hunt... Join Date: Sep 2006 Location: Portland, OR. Posts: 5,732	Re: WTB - looking for Vent Window Parts Hi Tony, we have a pair of NOS division bar felt channel runs available in the below linked "Several GM NOS 67-72 Truck Parts" f/s thread, listed as part/item #19. Have a look if interested in replacing the complete rear of vent wing channel. Mel http://67-72chevytrucks.com/vboard/s...d.php?t=798288 . Attached Images

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-12-2021, 05:43 PM	#1
71CHEVYSHORTBED402 Senior Member Join Date: Feb 2009 Location: Northern Nevada Posts: 7,322	WTB - looking for Vent Window Parts FOUND WHAT I WAS LOOKING FOR. Didn't know that bar was part of the assembly unit. Thank you. Discovered why my RH roll up window was so clumsy yesterday, getting T-boned will do that, took us five house to fit the door when the accident first discovered, bent pillar & that. Good news we feared the door was well plastered, but no, the guys did I nice job pulling out the dent, but they favored bondo over welds for the holes they drilled. Anyway the vent window is nice less a bent bar and bracket, loose rivets on the bracket. I straightened the bar to a major extent, enough to put the chrome edge back on. It's going in for a tune-up, - either way the bracket has to come off to finish straightening the bar, not a big deal. 1. I'd rather start with a good bracket, so looking for one of those for sure. 2. If it's out there, see the exterior chrome bezel in the picture. I think they're interchangeable left or right. Mine is real good, no pitting etc., better is better 3. Can be talked into the chrome edging for the felt if they're sharp. 4. Or just a vent window with nice parts described above. Thank you. Attached Images __________________ Tony 71 Custom Deluxe, SWB, 2WD, 402, A/C. I developed an assembly kit for restoring the (a) truck from the ground up. My build thread, and more on the assembly kit https://67-72chevytrucks.com/vboard/...d.php?t=730025 Last edited by 71CHEVYSHORTBED402; 03-15-2021 at 03:38 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.