292/ Sm465 one piece drive shaft - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Charlie71C10 · 03-22-2021, 08:18 PM

Hello all, does anyone have a 292/ sm465 combo running a 1 piece driveshaft? I have a 71 shortbed with this combo going in and would rather a 1 piece if at all possible. Any info would be appreciated. Thanks in advance

**'68OrangeSunshine** · 03-22-2021, 09:23 PM

Quote:

Originally Posted by Charlie71C10

Hello all, does anyone have a 292/ sm465 combo running a 1 piece driveshaft? I have a 71 shortbed with this combo going in and would rather a 1 piece if at all possible. Any info would be appreciated. Thanks in advance

Yeah. I have a '68 C/10 Stepside w/ 292 L6/SM 465 and one-piece propshaft. All Factory [Fremont CA]. 12-Bolt, 3.73 rear. Posi conversion later.

Charlie71C10 · 03-22-2021, 09:34 PM

You wouldn’t happen to have a pic of that set up would you? Or any recommendations on who to have build a driveshaft for it?

**'68OrangeSunshine** · 03-22-2021, 11:16 PM

Tomorrow, I can try to crawl under and shoot one.
You could Google the subject internally, by checking 67-72chevytrucksdotcom , instead of Web, in the box on the upper margins.

old51sedan · 03-23-2021, 09:16 AM

Quote:

Originally Posted by Charlie71C10

You wouldn’t happen to have a pic of that set up would you? Or any recommendations on who to have build a driveshaft for it?

I have a 69 SB, came from factory with a 250/350 turbo and I piece driveshaft. It now has a 292, 200-4R and the same I piece drive shaft with no alterations, with the exception of moving the trans support back about 5 inches, all factory drilled holes.

**'68OrangeSunshine** · 03-23-2021, 10:21 PM

It was raining cats and dogs today.

03-22-2021, 08:18 PM	#1
Charlie71C10 Registered User Join Date: Oct 2020 Location: Western Massachusetts Posts: 22	292/ Sm465 one piece drive shaft Hello all, does anyone have a 292/ sm465 combo running a 1 piece driveshaft? I have a 71 shortbed with this combo going in and would rather a 1 piece if at all possible. Any info would be appreciated. Thanks in advance

03-22-2021, 09:34 PM	#3
Charlie71C10 Registered User Join Date: Oct 2020 Location: Western Massachusetts Posts: 22	Re: 292/ Sm465 one piece drive shaft You wouldn’t happen to have a pic of that set up would you? Or any recommendations on who to have build a driveshaft for it?

03-22-2021, 11:16 PM	#4
'68OrangeSunshine Senior Member Join Date: Feb 2002 Location: Tucson, AZ USA Posts: 7,504	Re: 292/ Sm465 one piece drive shaft Tomorrow, I can try to crawl under and shoot one. You could Google the subject internally, by checking 67-72chevytrucksdotcom , instead of Web, in the box on the upper margins. __________________ Every 25 years I like to rebuild that 292, whether it needs it or not.

03-23-2021, 10:21 PM	#6
'68OrangeSunshine Senior Member Join Date: Feb 2002 Location: Tucson, AZ USA Posts: 7,504	Re: 292/ Sm465 one piece drive shaft It was raining cats and dogs today. __________________ Every 25 years I like to rebuild that 292, whether it needs it or not.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.